skaraudio Posted March 15, 2012 Report Share Posted March 15, 2012 alot of people have a misconception that by lowering their ohm load to .5 they will get the same power increase as if they went from 2 to 1 ohm. It doesnt happen output increases very little and then current draw would go through the roof. for example i ran one 2500d at .5 and it had more draw than 2 of them at 1 ohm Some people are just stupid and buy the wrong coil configs. some dont plan ahead and they have one woofer wired to one ohm and then they buy a second woofer but not a second amp some people have a misconception that impedence rise will save their amp. The your amp will never see that load anyways crowd. This is very true. Also to answer the OP's question - I have customers who run the SK-1500 off stock electrical for daily use on 1/0 Power Run that see no problems. This is not the standard for most here but will probably work - you just won't see the voltage you really should be looking for. I would recommend at the minimum a small battery in the back and a Big 3 upgrade would most certainly add to the benefit with minimal cost. Quote Skar Audio www.SkarAudio.comPhone : (888) 501-7527 Link to comment Share on other sites More sharing options...
teardrop Posted March 15, 2012 Report Share Posted March 15, 2012 im just running the skar 800.1 on a d975 xspower under hood big 3 and all 1/0 wire on stock 130 amp alt Quote Link to comment Share on other sites More sharing options...
TheNewbie Posted March 15, 2012 Report Share Posted March 15, 2012 im just running the skar 800.1 on a d975 xspower under hood big 3 and all 1/0 wire on stock 130 amp alt How's your volatge? I was going to run the exact same setup.. but Skar 1500.1 90 amp alt. Everything else the same, 975, big three, 0 gauge. Quote Check out my build log: http://www.stevemead...60#entry1958353 Different folks have different strokes. Link to comment Share on other sites More sharing options...
teardrop Posted March 15, 2012 Report Share Posted March 15, 2012 (edited) waiting on custom box from skar audio but i don't see a problem comming up on voltage i have a volt meter and ill let ya know when i get it all up and running but it should be fine im running two ivx 15s it should be bumping by the weekend i hope iv already got the amp mounted and all the wiring done just gota get the box mount the subs and wire the subs to amp Edited March 15, 2012 by teardrop Quote Link to comment Share on other sites More sharing options...
Banshee421 Posted March 15, 2012 Author Report Share Posted March 15, 2012 Yea i was just throwing the .5 ohm thing out there I really thought it would give the same boost like 2 ohm to 1 ohm. if not im not doing it. Thats why I posted it now I know 1 ohm min for me. So dvc 4 ohm wired in parallal equals 2 ohm so the amp has 2 outputs. So just put 2 dvc4 wired in parallal in each output by its self and I will has 1 ohm right. Quote Link to comment Share on other sites More sharing options...
TheNewbie Posted March 15, 2012 Report Share Posted March 15, 2012 waiting on custom box from skar audio but i don't see a problem comming up on voltage i have a volt meter and ill let ya know when i get it all up and running but it should be fine im running two ivx 15s Okay thanks man, lemme know! Quote Check out my build log: http://www.stevemead...60#entry1958353 Different folks have different strokes. Link to comment Share on other sites More sharing options...
TheNewbie Posted March 15, 2012 Report Share Posted March 15, 2012 Yea i was just throwing the .5 ohm thing out there I really thought it would give the same boost like 2 ohm to 1 ohm. if not im not doing it. Thats why I posted it now I know 1 ohm min for me. So dvc 4 ohm wired in parallal equals 2 ohm so the amp has 2 outputs. So just put 2 dvc4 wired in parallal in each output by its self and I will has 1 ohm right. www.the12volt.com Quote Check out my build log: http://www.stevemead...60#entry1958353 Different folks have different strokes. Link to comment Share on other sites More sharing options...
Guest Posted March 15, 2012 Report Share Posted March 15, 2012 Yea i was just throwing the .5 ohm thing out there I really thought it would give the same boost like 2 ohm to 1 ohm. if not im not doing it. Thats why I posted it now I know 1 ohm min for me. So dvc 4 ohm wired in parallal equals 2 ohm so the amp has 2 outputs. So just put 2 dvc4 wired in parallal in each output by its self and I will has 1 ohm right. two dual 4 woofers wired in parallel (all +'s together and all -'s together) will equal 1 ohm you can use either one of the amps outputs, or both sets. doesnt matter. Quote Link to comment Share on other sites More sharing options...
teardrop Posted March 15, 2012 Report Share Posted March 15, 2012 waiting on custom box from skar audio but i don't see a problem comming up on voltage i have a volt meter and ill let ya know when i get it all up and running but it should be fine im running two ivx 15s Okay thanks man, lemme know! link to my build log http://www.stevemeadedesigns.com/board/topic/119417-skar-audio-blazer-build/page__hl__%2Bskar+%2Baudio+%2Bblazer__fromsearch__1 Quote Link to comment Share on other sites More sharing options...
Banshee421 Posted March 15, 2012 Author Report Share Posted March 15, 2012 (edited) So the amp is parallal inside Edited March 15, 2012 by Banshee421 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.