Basshead89 Posted September 17, 2012 Report Share Posted September 17, 2012 Find some Q-Forms if you can. It will give you another spot for mids and Highs... Here is what I did in my 1992 F-150 4X4 If you want to you can reinforce them with fiberglass on the inside like I did. Link to comment Share on other sites More sharing options...
scooter99 Posted September 17, 2012 Author Report Share Posted September 17, 2012 Those do look good. But I'm using Bullet Tweets not the small domes. I think I'm good on the set up now. I just need to get started on it. Facebook Page: S99Creations 2006 F250 Lariat Build Link to comment Share on other sites More sharing options...
Purplehaze Posted September 21, 2012 Report Share Posted September 21, 2012 Looks good! Now to get it done! Kickin' Cruiser Seller Feedback Stage 3 Dash, Door Panels,4th Order wall 4 - 15'son a DC 5.0K 2 DC 5.0K'sSolo X 15 (v.2) Sub Build Link to comment Share on other sites More sharing options...
scooter99 Posted September 28, 2012 Author Report Share Posted September 28, 2012 Facebook Page: S99Creations 2006 F250 Lariat Build Link to comment Share on other sites More sharing options...
scooter99 Posted September 28, 2012 Author Report Share Posted September 28, 2012 Ok here goes! Check this out! Got the Box out and prepped it up! This has to be done before anything else can be built inside of it or for it. Some different views. Got it tapped up and then drew my line. I decided on a 1/2", but I probably should've gone more like 1". Oh well. Now, on the back of the truck is not a bad place to do it, however, it's just too tall. So I decided to put it on some sawhorses to bring it down more to my level. This does tell me, however, that when this is all said and done, I'll be able to load it into the truck pretty easily from the saw horses! But, that won't be for a while I'm sure! Now it's time for some fun! Safe fun, but fun! Got the gloves, got the safety glasses, don't need any metal in the eyes. And then the good ole trusty bosch grinder! This is a good tool! Facebook Page: S99Creations 2006 F250 Lariat Build Link to comment Share on other sites More sharing options...
scooter99 Posted September 28, 2012 Author Report Share Posted September 28, 2012 Then fun ensued, and this was the result! Let me give you a little tip if you've never done this, as I hadn't! WEAR LONG SLEEVES AS WELL AS GLOVES AND GLASSES!! Anyway, moving on, here's what we were after! Got some jagged edges that need addressing Little look at the amount of space I'm working with. Depth Width Couldn't really get a good measurement on the height cause the centers bow a bit. So it's basically about 17 3/4" tall. Then I got the grinder again with a grinding wheel this time, and cleaned up the edges! Burrs are gone! Tried to get a sight down pic to show the line, but it isn't real clear. Another pic with the smoothed edges. Facebook Page: S99Creations 2006 F250 Lariat Build Link to comment Share on other sites More sharing options...
scooter99 Posted September 28, 2012 Author Report Share Posted September 28, 2012 Then I decided that i still had some time before the family gets home, I thought I'd cut some wood! Love the smell of fresh cut wood! Especially Birch! Got my measurement for the bottom panel. This needs a couple angle cuts, which happen to be 45's. So I got my straight edge out, and measured it out. I need a final of 25" for my depth. Let's get to cutting! Yep, that'll do! Not bad with a straight edge and a hand saw! No table saw used here! Now for a little test fit. This is a little deceiving because of the bow in the middle. I pushed on it and laid it down and it fits perfectly. There is a little issue though. That is that I'm putting deadener on the inside of this box, between it and the enclosure, so I'll need to account for that. But I think it'll be fine. So that's what I got done tonight! I'm gonna see if I can get a couple things done here and there and get this thing built. We all know though, just building the enclosure is not the end of it. Lots of glasswork, and other odds and ends that need to be done. So, just as a refresher, this is what's going in: DC Audio XL 15's And this is what they're going in, what I'm building now: More to come! Thanks for tuning in! Facebook Page: S99Creations 2006 F250 Lariat Build Link to comment Share on other sites More sharing options...
Leo1103 Posted September 28, 2012 Report Share Posted September 28, 2012 m2's? 2002 Honda CR-VAlpine 9887My BuildRebuilding... Second Skin Damp 4 DC XL 15's 2 DC 5ks Singer 320 amp 6 cap banksSky High wire 2 VM-1's OM-1 all under window line Team DC Audio Obama has a law he's trying to pass right now, trying to ban Leo for being a threat to children everywhere.EDIT: Not in a JP kind of way. I thought I was going to die from all the jizz filling my ears. Link to comment Share on other sites More sharing options...
n1ghtsn1p3r Posted September 28, 2012 Report Share Posted September 28, 2012 This is looking awesome so far. And yeah, I feel you on the master cylinder and booster part. I've had to go through a few of them on my 86 Bronco II, which I had to retire earlier this year due to the same engine issues coming up over and over again. It got too expensive, plus it was "totalled" anyway (got rear-ended and my spare tire carrier punched right through my liftgate ). Having it break down on me every few months got annoying, since my job requires a lot of driving (I've done up to about 5000 miles in about a month ) 2016 Ford Focus SE No build log yetDC Audio 1.2K2x DC Audio Level 2 10" Link to comment Share on other sites More sharing options...
Purplehaze Posted September 28, 2012 Report Share Posted September 28, 2012 Ahh yeah! That is going to be hella cool when it done! Subs look sic too, I like the white baskets! Kickin' Cruiser Seller Feedback Stage 3 Dash, Door Panels,4th Order wall 4 - 15'son a DC 5.0K 2 DC 5.0K'sSolo X 15 (v.2) Sub Build Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.