Guest SyKo13 Posted December 31, 2006 Report Share Posted December 31, 2006 Since it tells me that.... I was wondering if I could take off a fan from my old pc and put it on this pc...... It's possible to my knowledge, but where do I connect it? Quote Link to comment Share on other sites More sharing options...
Amalan Posted December 31, 2006 Report Share Posted December 31, 2006 yessir look for a cable like most computers will have an extra power pin sprouting off one of the cables for future add ons so just look for one of those if not you will have to buy a splitter Quote Link to comment Share on other sites More sharing options...
Guest SyKo13 Posted December 31, 2006 Report Share Posted December 31, 2006 Yep, thanks :ninja: Quote Link to comment Share on other sites More sharing options...
Dale Posted December 31, 2006 Report Share Posted December 31, 2006 Syko, you're saying that you KNOW something's over-heating? Quote Link to comment Share on other sites More sharing options...
Guest SyKo13 Posted January 1, 2007 Report Share Posted January 1, 2007 Well after running this test..... That fire trash thing doesn't look so good lol, yet I have no clue what "Remote" is Quote Link to comment Share on other sites More sharing options...
Guest SyKo13 Posted January 1, 2007 Report Share Posted January 1, 2007 sHiiiiiiiiiiiiiiiitttttt lol Quote Link to comment Share on other sites More sharing options...
Amalan Posted January 1, 2007 Report Share Posted January 1, 2007 "First of all, you have to identify which temperature sensor is which. SpeedFan strictly adheres to available datasheets for each sensor chip. Please remember that hardware monitors are chips that do have some pins (small connectors) which should be connected to some additional hardware (temperature probes, thermistors or thermocouples) in order to be able to read temperatures. Only a few hardware monitor chips do label their connectors with "CPU", "System" and the like. Most of them use labels like "Temp1", "Local" or "Remote". The hardware manufacturers connect available pins to different temperature sensors basically according to the physical placement of components on the motherboard. This means that the same chip, an ITE IT8712F, for example, might be connected to a sensor diode measuring CPU temperature on Temp2 and, on a different hardware, it might be connected on Temp1. If you have a "Local" sensor and a "Remote" labeled one, this usually means that "Local" is the temperature of the monitor chip itself and "Remote" is the temperature read from a "remote" probe.When you have properly identified which temperature sensor is which, try to lower the speed of each fan and look at reported speed and temperatures. If you do not allow SpeedFan to change any fan speed and set all the speeds too low, then SpeedFan won't be able to avoid overheating. " Quote Link to comment Share on other sites More sharing options...
Guest SyKo13 Posted January 1, 2007 Report Share Posted January 1, 2007 O I C..... MEH, DON'T FEEL LIKE TRYING TO READ THE TINY WORDS Quote Link to comment Share on other sites More sharing options...
Amalan Posted January 1, 2007 Report Share Posted January 1, 2007 ok fine you pineapple flavored cunt "First of all, you have to identify which temperature sensor is which. SpeedFan strictly adheres to available datasheets for each sensor chip. Please remember that hardware monitors are chips that do have some pins (small connectors) which should be connected to some additional hardware (temperature probes, thermistors or thermocouples) in order to be able to read temperatures. Only a few hardware monitor chips do label their connectors with "CPU", "System" and the like. Most of them use labels like "Temp1", "Local" or "Remote". The hardware manufacturers connect available pins to different temperature sensors basically according to the physical placement of components on the motherboard. This means that the same chip, an ITE IT8712F, for example, might be connected to a sensor diode measuring CPU temperature on Temp2 and, on a different hardware, it might be connected on Temp1. If you have a "Local" sensor and a "Remote" labeled one, this usually means that "Local" is the temperature of the monitor chip itself and "Remote" is the temperature read from a "remote" probe. When you have properly identified which temperature sensor is which, try to lower the speed of each fan and look at reported speed and temperatures. If you do not allow SpeedFan to change any fan speed and set all the speeds too low, then SpeedFan won't be able to avoid overheating. " Quote Link to comment Share on other sites More sharing options...
Dale Posted January 1, 2007 Report Share Posted January 1, 2007 Felt like someone slapped an inch-thick pair of reading glasses to my face. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.