lacerda88 Posted May 9, 2010 Report Share Posted May 9, 2010 (edited) Hello guys, I have assembled a sound on my PC, just like in the picture with the following equipment: > Pioneer P6850MP AMP 480rms Band for bass, one on each SUB Bridge Buster B. AMP 1600W 400rms to middleweight. Source Audio BL 140A MAX Battery 70A > Front speakers = 2 5x7 "Buster 2 Coaxial 5 "N.A.R > Rear speakers = 2 Pioneer 6x9 6993S > I have two subs NAR Audio 180rms each of the following specification = Box I use is 38L each chamber. Diameter = 12 " Power 180W rms = FS = 23,80hz QES = 0.592 QMS = 4.024 QTS = 0.516 VAS - Lts = 190.0 Xmax = 7.5 mm in -% = 0.419 Sens 1w / m = 88.24 Sd = 53.093 m2 Le = 3.2 mH Re = 3.3 BL - T.M = 8.85 Impedance 4ohms = > Based on these parameters, can someone calculate the measures and pass me a box that it is excellent for this SUB? Fotos = Thank you. Edited May 9, 2010 by lacerda88 Quote Link to comment Share on other sites More sharing options...
scottx Posted May 10, 2010 Report Share Posted May 10, 2010 (edited) Haha! I've been running a kicker amp on a 10 in the house on my computer for almost 2 years. A simple little power 400 watt pc power supply powers the amp. It sounds really good. Kicker KX 200.4 bridged on a dual 4 ohm mtx sub in a radio shack pa box with crossover. Tweeter disconnected. Edited May 10, 2010 by scottx Quote Loud and Clean - 1985 190e 2.3 Audio Show Car - Champagne Dream. Link to comment Share on other sites More sharing options...
inm Posted May 10, 2010 Report Share Posted May 10, 2010 Would you happen to have a wiring diagram of how you wired everything up? Quote On 2/28/2013 at 2:52 PM, Chaise said: "Now spread your butt cheeks so I can zap your asshole." 2008 Subaru Forester XT Link to comment Share on other sites More sharing options...
lacerda88 Posted June 30, 2010 Author Report Share Posted June 30, 2010 Anyone can calculate a box for my SUBS with the following parameters? Thank you! Diameter = 12 " Power 180W rms = FS = 23,80hz QES = 0.592 QMS = 4.024 QTS = 0.516 VAS - Lts = 190.0 Xmax = 7.5 mm in -% = 0.419 Sens 1w / m = 88.24 Sd = 53.093 m2 Le = 3.2 mH Re = 3.3 BL - T.M = 8.85 Impedance 4ohms Quote Link to comment Share on other sites More sharing options...
Explorer Posted July 2, 2010 Report Share Posted July 2, 2010 (edited) Anyone can calculate a box for my SUBS with the following parameters? Thank you! Diameter = 12 " Power 180W rms = FS = 23,80hz QES = 0.592 QMS = 4.024 QTS = 0.516 VAS - Lts = 190.0 Xmax = 7.5 mm in -% = 0.419 Sens 1w / m = 88.24 Sd = 53.093 m2 Le = 3.2 mH Re = 3.3 BL - T.M = 8.85 Impedance 4ohms Make it 500mm x 500mm x 400mm then its tuned to 30hz Dimensions are internal Box for one sub is 100l Edited July 2, 2010 by Explorer Quote Link to comment Share on other sites More sharing options...
Liighthead Posted August 20, 2010 Report Share Posted August 20, 2010 how u keep the battery charged? nice setup btw Quote Link to comment Share on other sites More sharing options...
Socky Posted August 21, 2010 Report Share Posted August 21, 2010 how u keep the battery charged? nice setup btw I think its the power supply in the picture at the bottum charging the battery. Quote Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz Link to comment Share on other sites More sharing options...
Liighthead Posted August 23, 2010 Report Share Posted August 23, 2010 I think its the power supply in the picture at the bottum charging the battery. ow didnt see that... they expensive? Quote Link to comment Share on other sites More sharing options...
lacerda88 Posted August 25, 2010 Author Report Share Posted August 25, 2010 Hello staff, the source is black in the picture with the name BL AUDIO. She has 140A and maintains the battery charge, for use only with the sound attached to it. About my question, the ideal is to make a box for each sub with 100L? I'll have a good quality with my subs? thanks. Quote Link to comment Share on other sites More sharing options...
almaha76 Posted September 15, 2010 Report Share Posted September 15, 2010 You are really great. Keep it up. Quote CNA Certification Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.