peacedisturbance Posted October 31, 2010 Report Posted October 31, 2010 i was wondering how i would wire 6 dual 4 ohm subs and what the lowest impedance i could get i am looking to get 2 ohms can any one help me Quote Currently in a build 2 BTL 18s 1 AQ 2200 4 Kenetic hc 600s Pioneer AVH-P2300 (next purchase) High output alt 150 amps
victor83007 Posted October 31, 2010 Report Posted October 31, 2010 I don't know but I think you need 2 amplifiers and then 3 subwoofers to each amplifier Quote
loburbon Posted October 31, 2010 Report Posted October 31, 2010 wire each sub up to 8ohm then wire them back down to get a 1.33 ohm load Quote 2000 gmc yukon 4 sundown Zv3 15's 4 dd m2a's kenwood kdc-x994 2 batcap 4000's 1 batcap 2000 dual alts. 154@37hz and climbing http://www.cardomain.com/ride/3231683 http://www.myspace.com/torque150
__d_a_v_i_d__ Posted October 31, 2010 Report Posted October 31, 2010 wire each sub up to 8ohm then wire them back down to get a 1.33 ohm load but thats not the lowest imp. 6 DVC drivers with Voice Coils in Parallel / Parallel Dual-4 Ohm Subwoofers: 0.33 Ohm Quote Chevy Impala Shocker Sigs / TC Sounds 12s Sundown NS-1 | SAX 100.4 Sundown Neos | Dayton Audio Neos ETCCC ETCCC ETCCC My YouTube ---- Subcribe!!
victor83007 Posted October 31, 2010 Report Posted October 31, 2010 Check this out http://www.the12volt.com/caraudio/woofer_configurations.asp?Q=3&I=42 Quote
peacedisturbance Posted October 31, 2010 Author Report Posted October 31, 2010 wire each sub up to 8ohm then wire them back down to get a 1.33 ohm load is it possible to wire it all in parrales then the last sub in serries to increase the impedance Quote Currently in a build 2 BTL 18s 1 AQ 2200 4 Kenetic hc 600s Pioneer AVH-P2300 (next purchase) High output alt 150 amps
__d_a_v_i_d__ Posted October 31, 2010 Report Posted October 31, 2010 is it possible to wire it all in parrales then the last sub in serries to increase the impedance // dont get what your sayng, having one sub at 8 ohms will the rest are in 2ohms? no. if you have any decent amp, stable atone ohm. 1.33 is perfect. Quote Chevy Impala Shocker Sigs / TC Sounds 12s Sundown NS-1 | SAX 100.4 Sundown Neos | Dayton Audio Neos ETCCC ETCCC ETCCC My YouTube ---- Subcribe!!
peacedisturbance Posted October 31, 2010 Author Report Posted October 31, 2010 // dont get what your sayng, having one sub at 8 ohms will the rest are in 2ohms? no. if you have any decent amp, stable atone ohm. 1.33 is perfect. ok lol do u think there is a diagram or should i just keep playing around with the wireing and look at my multi meter Quote Currently in a build 2 BTL 18s 1 AQ 2200 4 Kenetic hc 600s Pioneer AVH-P2300 (next purchase) High output alt 150 amps
ingramcaraudio Posted October 31, 2010 Report Posted October 31, 2010 How i did mine just series all the subs then parallel the wires coming from the subs and you should get 1.33333. Quote Facebookhttp://www.facebook.com/#!/pages/Farmville-VA/Rockwell-Audio/103036213076623?ref=ts
uhoh_45 Posted October 31, 2010 Report Posted October 31, 2010 go to bottom Quote R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.