corteznewbie
-
Posts
1724 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Everything posted by corteznewbie
-
bad ass -
yuppers but inverted
-
well shit no matter how i do the measurements i still end up with 7.3 cubes for the box. unless you can come up with somethen obi. i read some where on here a guy had a 8 cube box for his 12's and he just kept the gain down cuz he said it was 2 efficient. i just wanna hit low as possible for now
-
but how would i do the port? and how would i position them. i was gonna the basic 4 on top.
-
what if i stick with 2 12's and still do 30hz?
-
1200rms and they will be inverted just waiten til my other 2 get here
-
for now the planet audio bb2 12's and the planet audio bb2 2400 but my amps bc said it was tested at 2,150 watts at 14.4 but my jeep only lets me get 13.8 13.9 at the most til i get a adjustable voltage reg
-
but like i stated b4 i only have 2 of my 4 sub for now and and only wanna build one box do to budget so how bad would this effect the subs?
-
well if i go 33w 26h26 d and do 8hx12w x20d port gives me 11.25 in the port area per foot at 30.75 hz
-
so should i go higher or wider to achieve that
-
k and part 2 of my question will that box be to much for 2 12's until my other 2 get here
-
the port area per foot says 5.72 squared. and i'm using a 2"x4" by 24" board just cuz its free and handy
-
well today i shall attempt my new box w/ sum help do to a injury. anyways according to the calculator if i build the box thats 32w 24 h and 26 d and a port thats 3 h 16 w and 9 d will give me 30.83 hz. subs will be inverted and will be roughly 8.84 cubic fee. big enough for 4 12" subs. my question is the port area enough and how would i calculate the 2x4 that i will be usen for center bracing.
-
and planet audio i'm picking up my new bb2400 amp today to go alot with the bb2 12's
-
watch out for tech the forum smart ass lol and have fun in here
-
can i get it to lol
-
woofer break in.
corteznewbie replied to rasic's topic in General Audio - Can't find a category for your question? Ask here.
save sum chix for us chode -
theres like 8 e bay stores that carry that amp
-
is that store honorable?
-
i just wish i knew where to get a ap3000 it will work perfect for my set up
-
i been told that to
-
jeeps are uni bodied there for if he uses the factory bolt still a chassis ground just make sure its bare metal
-
sand down the factory spot then there should be a bolt that holds ya coil pack to the block so one ground to the inner fender andone wire to the bolt that holds ya coil
-
EXO comment
corteznewbie replied to corteznewbie's topic in Member Videos - Host 'em & Post 'em! System Vids / Off Topic
fact peel n seal isnt always asphalt they do make a thick 70mil rubber based version stop by lowes a read the lable. fat mat is fancy peal n seal and other than waiten for a voltage regulater and one more battery my electrical is stout enough for my set up. now when i get a all out comp car then yes i'll get the good stuff -
EXO comment
corteznewbie replied to corteznewbie's topic in Member Videos - Host 'em & Post 'em! System Vids / Off Topic
and yes i said peel n seal i dond have a xtra 250 bux in my system budget and it works just as well. just because it dont cost hundreds of dollars dont mean it aint good stufff