dirtracer27x Posted May 17, 2011 Report Share Posted May 17, 2011 ok so i m goin to install my comps today(cresecndo ccx65).but right now i have 2 sets of polk mm 6.5 coaxs running off of a soundstream rubicon 5.800.i have the amp runnin full range and also running a soundtream 3 way crossover.the reason for the crossover was because the amp is under the bow of the boat and alittle hard to get to.what is my best way to wire these two sets up?should i re run the rca to the amp and just run full range to comps?or can i leave it the way it is and run the thru the crossover? also i have 3 sets total,what is my best way to wire these to a 4 channel?thanks alpine 794 h/u 6 crescendo ccx 6.5 comps 4 polk db 6x9 3 ways 2 jl audio OG 12w6 v1 1 jl audio OG 10w6 v1 1 soundstream rubicon rubi5.800 5 channel 1 soundstream rubicon rubi2.600 2 channel 1 soundstream rubicon rubi800.1 mono class d 1/0 knu 6 farad soundtream cap soundstream bx 10 soundstream 3 way xover Link to comment Share on other sites More sharing options...
dirtracer27x Posted May 17, 2011 Author Report Share Posted May 17, 2011 anyone alpine 794 h/u 6 crescendo ccx 6.5 comps 4 polk db 6x9 3 ways 2 jl audio OG 12w6 v1 1 jl audio OG 10w6 v1 1 soundstream rubicon rubi5.800 5 channel 1 soundstream rubicon rubi2.600 2 channel 1 soundstream rubicon rubi800.1 mono class d 1/0 knu 6 farad soundtream cap soundstream bx 10 soundstream 3 way xover Link to comment Share on other sites More sharing options...
MrSkippyJ Posted May 17, 2011 Report Share Posted May 17, 2011 I would do the coax's on 2 channels and the components on the other 2 channels. F150: Stock 2019 Harley Road Glide: Amp: TM400Xad - 4 channel 400 watt Processor: DSR1 Fairing (Front) 6.5s -MMats PA601cx Lid (Rear) 6x9s - TMS69 Link to comment Share on other sites More sharing options...
baller95 Posted May 17, 2011 Report Share Posted May 17, 2011 I think everyone got distracted looking at your picture/avatar hahah !! Link to comment Share on other sites More sharing options...
dirtracer27x Posted May 18, 2011 Author Report Share Posted May 18, 2011 I think everyone got distracted looking at your picture/avatar hahah !! lol i actuall am getting rid of the polk mm coaxs,just gonna run comps for now.but i have this crossover in there and not sure how i should run them.can i just hook the comps up with the passive crossovers that came with the set?and adjust 3 way crossover?or should i rerun rca to just the amp and eliminate the 3 way xover? alpine 794 h/u 6 crescendo ccx 6.5 comps 4 polk db 6x9 3 ways 2 jl audio OG 12w6 v1 1 jl audio OG 10w6 v1 1 soundstream rubicon rubi5.800 5 channel 1 soundstream rubicon rubi2.600 2 channel 1 soundstream rubicon rubi800.1 mono class d 1/0 knu 6 farad soundtream cap soundstream bx 10 soundstream 3 way xover Link to comment Share on other sites More sharing options...
dirtracer27x Posted May 18, 2011 Author Report Share Posted May 18, 2011 its this amp: http://vi.ebaydesc.com/ws/eBayISAPI.dll?ViewItemDescV4&item=300548670344&t=1300891374000&ds=0&js=-1&ssid=0&seller=premier*electronics&category=18795&bv=msie&nv=2&sd=1&caz.html thru this crossover: http://www.sonicelectronix.com/item_23899_Soundstream-SE-3840.html to these comps: http://www.crescendoaudio.com/product.php?productid=17514&cat=0&page=0&featured=Y alpine 794 h/u 6 crescendo ccx 6.5 comps 4 polk db 6x9 3 ways 2 jl audio OG 12w6 v1 1 jl audio OG 10w6 v1 1 soundstream rubicon rubi5.800 5 channel 1 soundstream rubicon rubi2.600 2 channel 1 soundstream rubicon rubi800.1 mono class d 1/0 knu 6 farad soundtream cap soundstream bx 10 soundstream 3 way xover Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.