ChrisLun Posted January 6, 2012 Report Share Posted January 6, 2012 (edited) So I have this design by PWK, now the problem is is that when I first requested it , I stated I had 33"w but soon after I received the blueprint noticed I only had 32.5w....I email him back and this is what he said to do to correct the problem " If you have to take an inch off the width, remove it from the width of the chambers. Take 0.5” from each rear chamber and 1” off the front chamber. Do not alter the vents." Now my question is, where do I do that at...I dont want to mess up this design so if you guys know how can you please tell me. This is the first 6th order Ill be building and want to build it right. Edited January 6, 2012 by ChrisLun Quote 2006 Dodge Charger (2) Kinetic 3800 (1) DC Power 270XP (4) T1-12D4 (1) T2500BDCP (2) T400.4 7.5 cubic ft. (2) 6 in ports thru the rear deck (2) T165.2 (2) T169.3 Link to comment Share on other sites More sharing options...
ChrisLun Posted January 6, 2012 Author Report Share Posted January 6, 2012 Wanna start this build tomorrow....so bump Quote 2006 Dodge Charger (2) Kinetic 3800 (1) DC Power 270XP (4) T1-12D4 (1) T2500BDCP (2) T400.4 7.5 cubic ft. (2) 6 in ports thru the rear deck (2) T165.2 (2) T169.3 Link to comment Share on other sites More sharing options...
SQMonte Posted January 6, 2012 Report Share Posted January 6, 2012 It's late, kinda tired, but I think I understand what your're trying to do......simply subtract 1/2" from each of the panels that run width ways, that will leave the ports exactly the same.....just visualize removing 1/2" from the middle of each of those panels that run width ways, that'll give you that 1/2" back so the box will fit. Quote Alpine CDA-117...Memphis 16-X03 CDT Audio SQA-4100...SEAS Prestige H1396...Crescendo MP-6 Soundstream Rubicon 1.2500d...Digital Designs 3512f Link to comment Share on other sites More sharing options...
CaPRiCEx383 Posted January 6, 2012 Report Share Posted January 6, 2012 If I'm understanding this correctly, Off the top section you take off 1 inch. Then each of the bottom sections you take off .5 of an inch on each, preserving the ratio of the box but now it is with less box width now making it 32" Quote 90 Nissan 240sx Avic z-140bh Audison SR4 Audison Voce 6.5s CDT es-20 tweeters Sundown 1500v3 (2) DD 9510's 3 cube box 2 6" aeros XS Power D2400 & Xp950 Skyhigh/Knukonceptz/Rockford Fosgate wiring More Coming Soon.. Check my builds below. 97 Civic Hatch Build 86 Caprice Build you can pick up a chick in a car... I think it'd be hard to roll up mackin on a broad sittin on a sundown. My opinion Link to comment Share on other sites More sharing options...
CaPRiCEx383 Posted January 6, 2012 Report Share Posted January 6, 2012 I'm on mobile right now so i can't see the pic too well but, Of the top section, If it says 26.5, It should now be 25.5 and each of the bottom sections say 12.875 i think, It should now be 12.375 each. sorry if the numbers arent the same on the design, It's just what i can see Quote 90 Nissan 240sx Avic z-140bh Audison SR4 Audison Voce 6.5s CDT es-20 tweeters Sundown 1500v3 (2) DD 9510's 3 cube box 2 6" aeros XS Power D2400 & Xp950 Skyhigh/Knukonceptz/Rockford Fosgate wiring More Coming Soon.. Check my builds below. 97 Civic Hatch Build 86 Caprice Build you can pick up a chick in a car... I think it'd be hard to roll up mackin on a broad sittin on a sundown. My opinion Link to comment Share on other sites More sharing options...
rasic Posted January 6, 2012 Report Share Posted January 6, 2012 nice, whos this box going to? lol Quote system: changes way to much... Link to comment Share on other sites More sharing options...
Jd1102 Posted January 6, 2012 Report Share Posted January 6, 2012 (edited) basically chop the box down the middle width wise and take a half inch on both sides out and then use that edit: keeping the center divider on the bottom 2 chambers Edited January 6, 2012 by Jd1102 Quote Link to comment Share on other sites More sharing options...
ChrisLun Posted January 6, 2012 Author Report Share Posted January 6, 2012 Ok, so I just cut my center divider .5 " on each side....cool Quote 2006 Dodge Charger (2) Kinetic 3800 (1) DC Power 270XP (4) T1-12D4 (1) T2500BDCP (2) T400.4 7.5 cubic ft. (2) 6 in ports thru the rear deck (2) T165.2 (2) T169.3 Link to comment Share on other sites More sharing options...
SQMonte Posted January 6, 2012 Report Share Posted January 6, 2012 I thought u only needed to regain half an inch? Quote Alpine CDA-117...Memphis 16-X03 CDT Audio SQA-4100...SEAS Prestige H1396...Crescendo MP-6 Soundstream Rubicon 1.2500d...Digital Designs 3512f Link to comment Share on other sites More sharing options...
Bump4life Posted January 6, 2012 Report Share Posted January 6, 2012 yea sub track an inch from bigger chamber and .5inch form both smaller chambers width wise. And just out of curiosity, where does woofer get mounted? I have no experience with anything besides a basic slot box and would be interested in how these boxes work. Quote Buyer/Seller Feedback Thread: http://www.stevemead...5015-bump4life/ MB C220 153 Trunk Car Build Log: http://www.stevemead...d/#entry1840136 MB C280 Ipad Dash SQ Build Log: http://www.stevemeadedesigns.com/board/topic/194484-bump4lifes-new-benz-tony-c-relay-kit-pictures-ce-electric-audison-front-stage-installed/ My SPL Log: http://www.stevemead...__fromsearch__1 BMW M340 xDrive Stock, for now. Corner Load 10" maybe soon. But does 10s in the 1/4... Best Scores out of a trunk 153.0 sealed legal full tilt clamped 5524 @ 42 hz 154+ windows down, 155+ kick Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.