Real96SS Posted August 19, 2012 Report Share Posted August 19, 2012 Got a chance to use my new clamp meter. I have the exact same one that Jacob uses in his clamp videos. It shows the output power in Kw right on the screen. The voltage was dropping into the 12's so the 12.9 is a guesstimate. Either way it put out some good numbers and those will only go up once I swap out my wire. Enjoy and post your videos or numbers also. Quote Vehicle 2007 Chevrolet Avalanche(Co-Co) DNX9980HD 6 Team Fi 15's(King Edition) 3 DC 9k's 8 Nendo PWX 8's 4 Custom Steg 4" Super Tweeters 1 DC Audio 175.4 1 DC Audio 90.4 Rockford 360.3 3 DC Power 370xp Alts(Externally regulated) 21 D1600's 2 D4800's All SMD RCA's AudioTechnix Deadner Viper Alarm My YouTube- http://www.youtube.c...NG?feature=mhee Link to buildlog- http://www.stevemead...4-15s-2-dc-9ks/ Link to UBL- http://www.stevemeadedesigns.com/board/topic/165059-ublkings-avalanchecoco-new-build-starting8-king-edition-15-team-fis-in-a-wallyes-a-wall/ Link to comment Share on other sites More sharing options...
thorshammer Posted August 20, 2012 Report Share Posted August 20, 2012 Nice vid! on average I've seen 9650 at 11.8v with a 1.01 reactive. Quote Link to comment Share on other sites More sharing options...
Real96SS Posted August 21, 2012 Author Report Share Posted August 21, 2012 Nice vid! on average I've seen 9650 at 11.8v with a 1.01 reactive. So any clue why I'm only seeing 8100 at .9? I'm going to do some more test but that's odd I'm only getting 8100 and your saying 9650 at pretty much the same loads. Could it be the amp? Quote Vehicle 2007 Chevrolet Avalanche(Co-Co) DNX9980HD 6 Team Fi 15's(King Edition) 3 DC 9k's 8 Nendo PWX 8's 4 Custom Steg 4" Super Tweeters 1 DC Audio 175.4 1 DC Audio 90.4 Rockford 360.3 3 DC Power 370xp Alts(Externally regulated) 21 D1600's 2 D4800's All SMD RCA's AudioTechnix Deadner Viper Alarm My YouTube- http://www.youtube.c...NG?feature=mhee Link to buildlog- http://www.stevemead...4-15s-2-dc-9ks/ Link to UBL- http://www.stevemeadedesigns.com/board/topic/165059-ublkings-avalanchecoco-new-build-starting8-king-edition-15-team-fis-in-a-wallyes-a-wall/ Link to comment Share on other sites More sharing options...
AA98hoe Posted August 21, 2012 Report Share Posted August 21, 2012 i wonder if haveing door an hatch open affects it.. i clamp mine sealed up just like dbdrag then burp... is that your peak freq? have you tried other freqs Quote TEAM DC AUDIO VEHICLE:98 chevy tahoe 2wd 3-4 drop HEADUNIT:alpine 9886 PREAMP:arcaudio FRONT STAGE:4-6 1/2s selinium,DD component set and 4-selinium tweeters in each door KICKPANELS:jl audio 5 1/4 REAR DOORS: dd components 6 1/2s HIGHS AMPS:zapco 750.2 on front doors,zapco an another 750.2 on kicks and rear doors SUBS:4-ascendant audio 18s with 5 spiders in a custom box built by KINGSUV SUB AMP: 2-dc7.5s ALTERNATORS: 3-mechmans 1- 425comp, 1-smd spec350, 1-270 with adj voltage harness on custom dc bracket WIRE:10-runs 0g front to back BATTERIES:6-d1400s TL results:157.1 at 38hz and 156.8 at headrest score @37hz. STATE AND NATIONAL RECORD IN MECA S5. Link to comment Share on other sites More sharing options...
Real96SS Posted August 22, 2012 Author Report Share Posted August 22, 2012 i wonder if haveing door an hatch open affects it.. i clamp mine sealed up just like dbdrag then burp... is that your peak freq? have you tried other freqs My peak is 42hz and I can try it with the doors closed and different frequencies. i just used 40 cause it was close to peak frequency. Quote Vehicle 2007 Chevrolet Avalanche(Co-Co) DNX9980HD 6 Team Fi 15's(King Edition) 3 DC 9k's 8 Nendo PWX 8's 4 Custom Steg 4" Super Tweeters 1 DC Audio 175.4 1 DC Audio 90.4 Rockford 360.3 3 DC Power 370xp Alts(Externally regulated) 21 D1600's 2 D4800's All SMD RCA's AudioTechnix Deadner Viper Alarm My YouTube- http://www.youtube.c...NG?feature=mhee Link to buildlog- http://www.stevemead...4-15s-2-dc-9ks/ Link to UBL- http://www.stevemeadedesigns.com/board/topic/165059-ublkings-avalanchecoco-new-build-starting8-king-edition-15-team-fis-in-a-wallyes-a-wall/ Link to comment Share on other sites More sharing options...
thorshammer Posted August 22, 2012 Report Share Posted August 22, 2012 Nice vid! on average I've seen 9650 at 11.8v with a 1.01 reactive. So any clue why I'm only seeing 8100 at .9? I'm going to do some more test but that's odd I'm only getting 8100 and your saying 9650 at pretty much the same loads. Could it be the amp? I wouldnt be concerned at all. Currently I'm seeing 4300 at 1.1 reactive. Box has incredibly low reactive. If I turn it up any more, 1 click, it drops to low and protects lol Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.