COLTON94 Posted November 10, 2012 Report Share Posted November 10, 2012 How do the aqs sound im thiniing bout getting those and the supertweets Link to comment Share on other sites More sharing options...
jarrius Posted November 10, 2012 Report Share Posted November 10, 2012 LOVE IT LOVE IT im doing a 2001 escape just bought me a soundstream tarantula tx1.2000d. I cant wait to see more. 2012 Chevy sonic1xSQ HDC3 12 D2RF R1200d 140 square foot of Q-Mat(soon to be installed) 140.2Db sealed on the dash with TL 142 DB sealed on the dash with another meter (was dead on with the TL at a show i was at) 141 on music. strangeduck,on 02 Jan 2014 - 01:39 AM, said: when my car spins out i just put the car in neutral, turn in the direction i want to go and pucker my asshole Link to comment Share on other sites More sharing options...
KenC210 Posted November 10, 2012 Author Report Share Posted November 10, 2012 How do the aqs sound im thiniing bout getting those and the supertweets To be honest i have no clue and wont find out till my doors are done because i would rather wire everything once than take out seats and carpet each time i wanna run some wires for speakers. But once i get them playing im sure i have a lot of tuning to do. Thank you everyone for the comments there will be more but mostly i do the work during the week as i try to spend time with the family on weekends Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
KenC210 Posted November 15, 2012 Author Report Share Posted November 15, 2012 I also got started on the doors. A little bit at a time. A before shot of the door I have the ring cut out and it is wrapped with fleece just waiting to get glassed up If you compare to the before pic you will see what i am going to be relocating the pocket area to the rear part of the door. Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
KenC210 Posted November 19, 2012 Author Report Share Posted November 19, 2012 So i started to strip out everything all old wires remove the old speakers and start cleaning everything up so i could start putting deadener in. My giant mess of wires that i have to take out. everything is zip tied and wrapped with electrical tape. Also all wires were soldered and shrink wrapped. Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
KenC210 Posted November 19, 2012 Author Report Share Posted November 19, 2012 After i got the wires cleaned up and taken out i started to get test fitting the doors just to make sure they will fit still with the new speakers in. As you can see i needed to do some modified work here to make some clearance for the 6.5 and some more clearance for the pocket i relocated. The Pocket area. This is before I cut the area to fit the pocket. I forgot to get the after shot of the cut for the pocket. I could get a shot of it later but there is now deadener on it. The before shot of the 6.5 area i had to modify Why it didn't fit Before i had it cut The after shot of the modified area for the 6.5 The door fits good now Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
KenC210 Posted November 19, 2012 Author Report Share Posted November 19, 2012 The test fit for the 8 was perfect. I didn't have to cut or modify anything. Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
KenC210 Posted November 19, 2012 Author Report Share Posted November 19, 2012 Now to deaden the doors... And the vid of a comparison Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
FrontierGello Posted November 19, 2012 Report Share Posted November 19, 2012 After i got the wires cleaned up and taken out i started to get test fitting the doors just to make sure they will fit still with the new speakers in. As you can see i needed to do some modified work here to make some clearance for the 6.5 and some more clearance for the pocket i relocated. The Pocket area. This is before I cut the area to fit the pocket. I forgot to get the after shot of the cut for the pocket. I could get a shot of it later but there is now deadener on it. The before shot of the 6.5 area i had to modify Why it didn't fit Before i had it cut The after shot of the modified area for the 6.5 The door fits good now What did you use to cut the door panels? Nissan Frontier 10" Cadence Midbass 8" Cadnece Midrange Bullet tweets 2 Re audio Sxx 15 Subs Mechman 270a 2 Re XT4000deV3 mono 1600 rms 1 Re XT400deV3 Bridged 350x2 2 Cadence 175.4 Bridged 350x2 Audiomaxx and Stinger 0,4,8,12 awg wires Dynamat sound deadeners My Build Log: http://www.stevemead...__+1999 +nissan Link to comment Share on other sites More sharing options...
KenC210 Posted November 19, 2012 Author Report Share Posted November 19, 2012 After i got the wires cleaned up and taken out i started to get test fitting the doors just to make sure they will fit still with the new speakers in. As you can see i needed to do some modified work here to make some clearance for the 6.5 and some more clearance for the pocket i relocated. The Pocket area. This is before I cut the area to fit the pocket. I forgot to get the after shot of the cut for the pocket. I could get a shot of it later but there is now deadener on it. The before shot of the 6.5 area i had to modify Why it didn't fit Before i had it cut The after shot of the modified area for the 6.5 The door fits good now What did you use to cut the door panels? I used a cutting wheel Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.