Socky Posted April 11, 2013 Report Share Posted April 11, 2013 but remeber the obsidian is reconable and handle a little more power Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz Link to comment Share on other sites More sharing options...
ThreehundredC Posted April 11, 2013 Author Report Share Posted April 11, 2013 but if i did i would build a new box but use the same kicker zx750.1 amp until later when i decided to get more subs Link to comment Share on other sites More sharing options...
ThreehundredC Posted April 12, 2013 Author Report Share Posted April 12, 2013 so a beat on l7 swapped out for a brand new OA15 sound be an improvement Link to comment Share on other sites More sharing options...
ThreehundredC Posted April 23, 2013 Author Report Share Posted April 23, 2013 JOE or Somebody can you take the box design i currently have (blueprints are on pages before ) with 13.5 back height and 18 front height! Link to comment Share on other sites More sharing options...
ThreehundredC Posted April 23, 2013 Author Report Share Posted April 23, 2013 so i took the floor boards out and got the box to sit a inch lower so it slide back but still makes no diffrence in saved trunk space guess my only option is a tiny box for a l7 or a sealed box but who does that! Link to comment Share on other sites More sharing options...
Joe X Posted April 24, 2013 Report Share Posted April 24, 2013 If you really want to push back you need to do a box that's slanted on the back. Link to comment Share on other sites More sharing options...
ThreehundredC Posted May 5, 2013 Author Report Share Posted May 5, 2013 i want to make a 4th order witha sealed section at the back of the trunk and ported twards front or rear deck 6x9s and 8in woofer hole Link to comment Share on other sites More sharing options...
ThreehundredC Posted May 11, 2013 Author Report Share Posted May 11, 2013 well its another ported box with a bigger port than last time the box pictured above sold last week so i was riding all week with NO SUB! so i hadda remake a box got the box all done just need some connections for the wires to get out the box Do i just go to ace hardware and grab some bolts and wing nuts or what? Splatter port Link to comment Share on other sites More sharing options...
ThreehundredC Posted May 11, 2013 Author Report Share Posted May 11, 2013 should i just drill holes and run speaker wire out side the box then connected that wire to my amp wire, i want to be able to remove it every so often Link to comment Share on other sites More sharing options...
ThreehundredC Posted May 11, 2013 Author Report Share Posted May 11, 2013 well i drilled and filled the holes after pulling the wires thru took a test drive few minutes ago ...idk the 3.75 inch port was playing deep this one shakes more stuff in the cup holders n such might do better on a meter since its a higher tune but i love to dig down in the high 20s but its a more flashy box Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.