Audio Customs Posted December 12, 2012 Report Share Posted December 12, 2012 i just recently picked up a 1993 ford festiva 2D hatch im going to start my build on the first of the year ill be building door pannelsbefore i start building getting a car alarm firstthe equipmentHeadunit: Pioneer DEH-8400bhHighs/Mids: AQ-TS6.5 component set High/Mids Amp: p400.4Subwoofers: 2 SQ sdc 15D4Subwoofer Box: ported box 12.10 cubic foot tune to 34HZSubwoofer Amp: 1 RF p1000.1BD @ 1 ohm 1293 rmsbatteries 1 KHC1400 up front 1 KHC2000 in the backthe big 3 is doneso let me know if that design looks good im doing it like this for now untill i get more batts and alt and more subs and more POWER!!!im going to wall it later cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
elflako17 Posted December 12, 2012 Report Share Posted December 12, 2012 this ford fiesta is going to be banging 2010 Mazda 3 *Rebuild Time* Subs - (2) AA Mayhems 12's Sub amp - (1) Populus Audio TPA 6500 Headunit - Pioneer App Radio 2 Batteries - XS Power (1) D3100 up front | 6 XP950 rear Wire - Sky High 1/0 Gauge wires and RCA's and steve's VM1 Alternator - Singer 260 Externally Regulated Front Stage: (2) PRV Audio 10W650A (4) PRV Audio 8MR500-PhP-4 (4) DS Bullet Tweets | (2) 6.5 Components (Rear doors) Mids & high Amp : (2) Populus Audio 100.4 Processor: Rockford 3sixty.3 The Build Log : http://www.stevemeadedesigns.com/board/topic/175922-2010-mazda-3-2-aa-mayhems-12-pg14-new-video/page-11 Link to comment Share on other sites More sharing options...
Audio Customs Posted December 13, 2012 Author Report Share Posted December 13, 2012 i hope so cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
TheNewbie Posted December 13, 2012 Report Share Posted December 13, 2012 I'm not a box expert, but I think your port area is a bit low man. Check out my build log: http://www.stevemead...60#entry1958353 Different folks have different strokes. Link to comment Share on other sites More sharing options...
Audio Customs Posted December 14, 2012 Author Report Share Posted December 14, 2012 the box that i came up with it should do good im going to used birch cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
Audio Customs Posted December 14, 2012 Author Report Share Posted December 14, 2012 or this one 3/4 birch cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
Audio Customs Posted December 15, 2012 Author Report Share Posted December 15, 2012 so yesterday i was thinking of doing something different with the port im going to try kerfing this is my first time doing it its my practice run cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
Audio Customs Posted December 16, 2012 Author Report Share Posted December 16, 2012 i think im going with this box lot more port cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
Audio Customs Posted December 24, 2012 Author Report Share Posted December 24, 2012 so now im going to do a 4th order i have the room and its not going to have a wall box dims coming up cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
Audio Customs Posted December 24, 2012 Author Report Share Posted December 24, 2012 the sealed side and ported i can re adjust every thing if needed some one with experience with 4th order please chime in this is my first time building one thanks cone area http://www.stevemeadedesigns.com/board/topic/6819-cone-area-of-a-subwoofer/ 4th order band pass basic http://www.stevemeadedesigns.com/board/topic/126478-basics-of-a-4th-order-bandpass-enclosure/ this is Torres box calculator My GUI Box Tuning Calculator Download - Updated 8/18/2012 Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.