Ace Posted August 4, 2008 Author Report Share Posted August 4, 2008 thanks! tomorrow i hope to have the rear drop done. aim is jblackwell64www.jbcarworks.com Link to comment Share on other sites More sharing options...
Ace Posted August 7, 2008 Author Report Share Posted August 7, 2008 Well i got the 50lb bucket of aluminum oxide which is 10 times better then the glass i was using yesterday. i worked on it for about 4 hours and then spent 2 hours cleanin up the shop because after i got done with the truck today i could barely walk around. I also put leds in up in the markersand im buyin a new set of corners to do the tops because i didnt seal them with silicone and one cover fell off. ANY WAY.... on to the pics. and heres the rust from today only... prettty bad. Heres some pics of my shop. Pics of the leds aim is jblackwell64www.jbcarworks.com Link to comment Share on other sites More sharing options...
qu1cks1lver56 Posted August 7, 2008 Report Share Posted August 7, 2008 cant see the pics :[ First Gen Xterra: Always changing DNX 690HD RF 360.3RF T3002RF T4004RF T10001bdSilver Flute 6.5"s Tang Band 1" TweetersSundown X18 in 7cubes net tuned to 32hz Trust me .25 Blows your Load. Link to comment Share on other sites More sharing options...
Ace Posted August 7, 2008 Author Report Share Posted August 7, 2008 now u should aim is jblackwell64www.jbcarworks.com Link to comment Share on other sites More sharing options...
duct_tape123 Posted August 7, 2008 Report Share Posted August 7, 2008 Still no. Bandwidth exceeded Link to comment Share on other sites More sharing options...
Ace Posted August 7, 2008 Author Report Share Posted August 7, 2008 hm i just upgraded to pro and thats suppose to make it work. aim is jblackwell64www.jbcarworks.com Link to comment Share on other sites More sharing options...
Ace Posted August 8, 2008 Author Report Share Posted August 8, 2008 EVEN THO NO ONE CARES ILL KEEP POSTIN FOR A LITTLE WHILE AT LEAST well spent 1300 today on the truck on the new parts then went out and worked for 2 hours on one seat mount. I finally took them off and am gettin them ready for final install and i drilled the holes for the other side of the seat... only had one side mounted for the day that i drove it. Tomorrow i think the rear end is comin out. well see. First thing my dads gotten me for this build and by far one of the most needed. And some pics of where im at on the driver side mount... this stock paint is like concrete. aim is jblackwell64www.jbcarworks.com Link to comment Share on other sites More sharing options...
Ace Posted August 10, 2008 Author Report Share Posted August 10, 2008 I did get a bit done today, i started taking off the front clip and got the bumper and grille off and then got distracted on making the mount for my LS1 fans. It took me forever to make it because i dont have the proper tools to make it but i tried. Also got one of my two top corners set up to run an led in it too and got in my por 15 metal ready and marine clean. Anyway onto the pics. Disassembled front end. Buh bye fan Fan mount Goodies aim is jblackwell64www.jbcarworks.com Link to comment Share on other sites More sharing options...
Bass4Lyfe Posted August 10, 2008 Report Share Posted August 10, 2008 SHIT bro u doing work!! this all looks like hella hard work man awesome job ~Matthew 1998 Toyota Camry XLE V6 3L (1) ScyTek Astra 4000RS-2W-1 2-Way Remote Start Alarm with Shock and Proximity (1) 20% Tint All Around (Gately Audio) (1) 250 Amperage HO Alternator (1) Big 3 Done In 1/0 (2) Kinetik HC2400 Power Cell (1) Alpine IVA-D106 Receiver (1) Peripheral Video Bypass Device (4) Alpine SPS-17C2 Speakers (1) Alpine KCE-422i iPod Control Interface (4) Sheets Dynamat Extreme; for speakers (1) 10 Square Feet Hushmat (Trunk & Rear Deck) (4) DC Audio Level 4 15" D2 Subwoofer w/ Level 5 Coils (1) Wall Built By David, Tuned to 32 Hz (1) Rockford Fosgate T40001bd Amplifier (1) Stinger 1/0 Wiring (2 runs of + 2 runs of -) (1) Stinger Volt Meter Link to comment Share on other sites More sharing options...
Sampsonite Posted August 10, 2008 Report Share Posted August 10, 2008 Keep up the updates man, Great job so far! --Sampson 816-591-6592 www.kcrimshop.com Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.