ghostlyrich Posted November 18, 2013 Author Report Posted November 18, 2013 went on a bit of rant lol hope you get a laugh ups tryed to nail me pretty bad for a car battery charger i bought My youtube channel https://www.youtube.com/user/ghostlyrich Mazda 3 2006 Build (R.I.P) http://www.stevemeadedesigns.com/board/topic/172728-mazda-3-2006-stealth-build/ Volkswagen GTI 2011 Build http://www.stevemeadedesigns.com/board/topic/192979-vw-gti-2011-build/ Jeep 2015 Build http://www.stevemeadedesigns.com/board/topic/201493-my-new-jeep-2015/
rockFord_Expedition Posted November 18, 2013 Report Posted November 18, 2013 The very first pics of this thread show an enclosure with the ports firing into the trunk instead of into the cabin. Did that ever get fixed? Old School/New School RF Build March 2015 SOTM Winner How to crimp large wire
ghostlyrich Posted November 19, 2013 Author Report Posted November 19, 2013 The very first pics of this thread show an enclosure with the ports firing into the trunk instead of into the cabin. Did that ever get fixed? that was my very first set up lol never got fixed just replaced with the stealth box My youtube channel https://www.youtube.com/user/ghostlyrich Mazda 3 2006 Build (R.I.P) http://www.stevemeadedesigns.com/board/topic/172728-mazda-3-2006-stealth-build/ Volkswagen GTI 2011 Build http://www.stevemeadedesigns.com/board/topic/192979-vw-gti-2011-build/ Jeep 2015 Build http://www.stevemeadedesigns.com/board/topic/201493-my-new-jeep-2015/
rockFord_Expedition Posted November 19, 2013 Report Posted November 19, 2013 Oh. Nice work man. Way to stick to it. Old School/New School RF Build March 2015 SOTM Winner How to crimp large wire
dereileak Posted November 27, 2013 Report Posted November 27, 2013 Looking good, what was your alternator rated for? Mine is a mechman, but I can't get the full amperage out of it cause I believe the belt slips, even with a new tensioner, new gates green back belt and a shorter tighter belt, so idk, 2 runs of 2/0 wire too lol 2006 Mazda3 Hatchback Black 5 Spd ManualPioneer 4300DVD2 Sundown SA-12 (34hz Tune, 3.22 cubes, 14.5 inches per cube, Triple Baffle)Kicker 10ZX2500.1 (2845 RMS) Sub AmpKicker 11ZX650.4 (705 RMS) Mid Amp -- (3 Amps)Kicker KQ3 Active CrossoverKicker KQ30 EqualizerKicker 09QS60.2 Components (Woven Carbon Cones)Kicker 09QS65.2 Components (Woven Carbon Cones) - (3 Sets)2/0 Gauge Electron Beam Technologies (3 Runs, 2 +, 1 -) 1/0 Gauge KNU Kollasal Flex (1 Run for -) 300 Ft Kicker X-Series 16 Gauge Speaker WireXS Power D3400 (Rear)XS Power D3100 (Front)Singer Externally Regulated Alternator (Being Built)+ The Love for Car Audio and BASS <3UBL Build Log <------- Click Here-------> Normal Build Log (For Comments)
ghostlyrich Posted November 27, 2013 Author Report Posted November 27, 2013 Looking good, what was your alternator rated for? Mine is a mechman, but I can't get the full amperage out of it cause I believe the belt slips, even with a new tensioner, new gates green back belt and a shorter tighter belt, so idk, 2 runs of 2/0 wire too lol its rated for 200amp, 250 peak. haha could do 2 runs of zero XD My youtube channel https://www.youtube.com/user/ghostlyrich Mazda 3 2006 Build (R.I.P) http://www.stevemeadedesigns.com/board/topic/172728-mazda-3-2006-stealth-build/ Volkswagen GTI 2011 Build http://www.stevemeadedesigns.com/board/topic/192979-vw-gti-2011-build/ Jeep 2015 Build http://www.stevemeadedesigns.com/board/topic/201493-my-new-jeep-2015/
ghostlyrich Posted November 27, 2013 Author Report Posted November 27, 2013 mazda 3 had a rad flush My youtube channel https://www.youtube.com/user/ghostlyrich Mazda 3 2006 Build (R.I.P) http://www.stevemeadedesigns.com/board/topic/172728-mazda-3-2006-stealth-build/ Volkswagen GTI 2011 Build http://www.stevemeadedesigns.com/board/topic/192979-vw-gti-2011-build/ Jeep 2015 Build http://www.stevemeadedesigns.com/board/topic/201493-my-new-jeep-2015/
dereileak Posted December 1, 2013 Report Posted December 1, 2013 mazda 3 had a rad flush I changed my theromostat, which is common for it to go out in these cars after like 100k miles, did a flush then, but not as complicated as your way, I just followed this http://www.mazda3forums.com/showthread.php?t=284715 2006 Mazda3 Hatchback Black 5 Spd ManualPioneer 4300DVD2 Sundown SA-12 (34hz Tune, 3.22 cubes, 14.5 inches per cube, Triple Baffle)Kicker 10ZX2500.1 (2845 RMS) Sub AmpKicker 11ZX650.4 (705 RMS) Mid Amp -- (3 Amps)Kicker KQ3 Active CrossoverKicker KQ30 EqualizerKicker 09QS60.2 Components (Woven Carbon Cones)Kicker 09QS65.2 Components (Woven Carbon Cones) - (3 Sets)2/0 Gauge Electron Beam Technologies (3 Runs, 2 +, 1 -) 1/0 Gauge KNU Kollasal Flex (1 Run for -) 300 Ft Kicker X-Series 16 Gauge Speaker WireXS Power D3400 (Rear)XS Power D3100 (Front)Singer Externally Regulated Alternator (Being Built)+ The Love for Car Audio and BASS <3UBL Build Log <------- Click Here-------> Normal Build Log (For Comments)
dereileak Posted December 1, 2013 Report Posted December 1, 2013 Looking good, what was your alternator rated for? Mine is a mechman, but I can't get the full amperage out of it cause I believe the belt slips, even with a new tensioner, new gates green back belt and a shorter tighter belt, so idk, 2 runs of 2/0 wire too lol its rated for 200amp, 250 peak. haha could do 2 runs of zero XD so 200 idle? really that much? 2006 Mazda3 Hatchback Black 5 Spd ManualPioneer 4300DVD2 Sundown SA-12 (34hz Tune, 3.22 cubes, 14.5 inches per cube, Triple Baffle)Kicker 10ZX2500.1 (2845 RMS) Sub AmpKicker 11ZX650.4 (705 RMS) Mid Amp -- (3 Amps)Kicker KQ3 Active CrossoverKicker KQ30 EqualizerKicker 09QS60.2 Components (Woven Carbon Cones)Kicker 09QS65.2 Components (Woven Carbon Cones) - (3 Sets)2/0 Gauge Electron Beam Technologies (3 Runs, 2 +, 1 -) 1/0 Gauge KNU Kollasal Flex (1 Run for -) 300 Ft Kicker X-Series 16 Gauge Speaker WireXS Power D3400 (Rear)XS Power D3100 (Front)Singer Externally Regulated Alternator (Being Built)+ The Love for Car Audio and BASS <3UBL Build Log <------- Click Here-------> Normal Build Log (For Comments)
ghostlyrich Posted December 2, 2013 Author Report Posted December 2, 2013 Looking good, what was your alternator rated for? Mine is a mechman, but I can't get the full amperage out of it cause I believe the belt slips, even with a new tensioner, new gates green back belt and a shorter tighter belt, so idk, 2 runs of 2/0 wire too lol its rated for 200amp, 250 peak. haha could do 2 runs of zero XD so 200 idle? really that much? nah idle is not that high if i remember correct i think its around 120 My youtube channel https://www.youtube.com/user/ghostlyrich Mazda 3 2006 Build (R.I.P) http://www.stevemeadedesigns.com/board/topic/172728-mazda-3-2006-stealth-build/ Volkswagen GTI 2011 Build http://www.stevemeadedesigns.com/board/topic/192979-vw-gti-2011-build/ Jeep 2015 Build http://www.stevemeadedesigns.com/board/topic/201493-my-new-jeep-2015/
Recommended Posts
Archived
This topic is now archived and is closed to further replies.