caddylac Posted March 19, 2008 Report Share Posted March 19, 2008 this is prolly a stupid question but its the only thing holding me back from ordering wire. do i need a 4 channel rcas for a 4 channel amp. or do i just need 2 rcas like a subs amp. equipment http://www.rockfordfosgate.com/products/pr...S&p_status= http://www.woofersetc.com/index.cfm?fuseac...Product_ID=1078 http://www.woofersetc.com/index.cfm?fuseac...Product_ID=6183 rcas http://www.knukonceptz.com/productDetail.cfm?prodID=KRY4.6M or http://www.knukonceptz.com/productDetail.cfm?prodID=KRY2.1M Quote Link to comment Share on other sites More sharing options...
benz280se Posted March 19, 2008 Report Share Posted March 19, 2008 (edited) this is prolly a stupid question but its the only thing holding me back from ordering wire. do i need a 4 channel rcas for a 4 channel amp. or do i just need 2 rcas like a subs amp.equipment http://www.rockfordfosgate.com/products/pr...S&p_status= http://www.woofersetc.com/index.cfm?fuseac...Product_ID=1078 http://www.woofersetc.com/index.cfm?fuseac...Product_ID=6183 rcas http://www.knukonceptz.com/productDetail.cfm?prodID=KRY4.6M or http://www.knukonceptz.com/productDetail.cfm?prodID=KRY2.1M with this amp it can go four channel out with only two rca's in. you would need the other rca cables hooked into the other channels if you wanted front and rear fade capabilities and a little more stereo seperation. so its just on what you are planning to do. hope this helps Edited March 19, 2008 by benz280se Quote Link to comment Share on other sites More sharing options...
trainman0978 Posted March 19, 2008 Report Share Posted March 19, 2008 what he said ... you need to send all four channels from the deck to the amp to get proper fade and balance control out of your deck... Quote 2007 Toyota FJ Cruiser Voo Doo Blue my upgrades and "build" thread. My Kulicki Box Build -Alpine 9887 head unit, KTX-100EQ imprint-( sound quality for dummies! ). - MB Quartz 3.5" in back pillars -Sundown Audio SAX100.4 - JL Audio 3 way 6.5" component set XR653-CSi ( doors and dash ) -JL Audio 2 way Component set XR650CSi - Alpine MRD - M1005 - Alpine Type - R 12" subs -- 2 - 12" s in a Pete kulicki designed box. -Alpine High speed Ipod cable, and KCA-SC100 with Sirius sat. radio -All wiring is Stinger 12 gauge and HPM Level 3 RCAs, KnuKonceptz Kolossus Power and ground and Big done in 1/0, -270 sq. ft. of Damplifier Pro, 36 sq. ft. of Overkill Pro, 6 full sheets of Luxury Liner, and a gallon of spectrum- -2 Powermaster D680 Powercells in back FINALLY !!! I GOT IT METERED ON THE TERMLAB !!! I did a 140.2 at 42 hertz. Shoehorn, BFH, forklift,duct tape and some zip ties Link to comment Share on other sites More sharing options...
jmsonoma03 Posted March 19, 2008 Report Share Posted March 19, 2008 what he said ... you need to send all four channels from the deck to the amp to get proper fade and balance control out of your deck... use either a four ch rca or two two ch rca both will work Quote Link to comment Share on other sites More sharing options...
caddylac Posted March 19, 2008 Author Report Share Posted March 19, 2008 thatnks guys that made my life a lot easyer, one more question why does knukonceptz have the rcas measured in meters and how long would i need them for a 17 foot car. Quote Link to comment Share on other sites More sharing options...
mrwigglezdj Posted March 20, 2008 Report Share Posted March 20, 2008 1 meeter is 3 feet so you would need a 6 meeter or 5.5 meeter Quote Americas loudest work van2006 iasca heavyweight bassboxing champion at 150.4 db with 60second average TL8 memphis PR15s,12 memphis PR6.5's coax,4 memphis PR 1inch tweets Link to comment Share on other sites More sharing options...
caddylac Posted March 20, 2008 Author Report Share Posted March 20, 2008 ill go ahead and go with 6 meters to be safe. thanx maby i can go ahead and get this stuuf ordered tommorow. Quote Link to comment Share on other sites More sharing options...
caddylac Posted March 20, 2008 Author Report Share Posted March 20, 2008 damn it another question what guage of speaker wire should i run to my mids and high from the amp. Quote Link to comment Share on other sites More sharing options...
mrwigglezdj Posted March 20, 2008 Report Share Posted March 20, 2008 12-14ga. mainly depends on how much power youre puting thru the wire, im running 4 speakers per ch. so im useing 12ga myself to be on the safe side Quote Americas loudest work van2006 iasca heavyweight bassboxing champion at 150.4 db with 60second average TL8 memphis PR15s,12 memphis PR6.5's coax,4 memphis PR 1inch tweets Link to comment Share on other sites More sharing options...
caddylac Posted March 20, 2008 Author Report Share Posted March 20, 2008 thanx for the quick response, im go ahead and do 12 just incase also. that should be the last dumb question (prolly not) lol Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.