00sdime00 Posted July 24, 2008 Report Posted July 24, 2008 Not feelin the 50/50 link..looks like your pinion angle is a bit off at full lift..especially considering that it looks like it's a parallel setup with no watts link or even a panhard bar..I can't really tell for sure. Notch looks like it's made out of 2x3, but it seems that the frame has sagged a little. Either that or the bed is not put on correctly. If you plan on redoing it...I would just go ahead and backhalf it. It will save you a lot of time and trouble. These are just a few of my opinions and I hope you take them into consideration. I only point these things out for your safety and the safety of others. A half-wit gave you a piece of his mind, and you held on to it. My Youtube vids...enjoy anythings possible with the right build =] we accept visa and mastercard =]
Tub Asko Posted July 24, 2008 Author Report Posted July 24, 2008 Not feelin the 50/50 link..looks like your pinion angle is a bit off at full lift..especially considering that it looks like it's a parallel setup with no watts link or even a panhard bar..I can't really tell for sure. Notch looks like it's made out of 2x3, but it seems that the frame has sagged a little. Either that or the bed is not put on correctly. If you plan on redoing it...I would just go ahead and backhalf it. It will save you a lot of time and trouble. These are just a few of my opinions and I hope you take them into consideration. I only point these things out for your safety and the safety of others. Yea bed is coming off first thing to redo that mess that's under there. The gas tank is being held up by a damn ratchet strap so it's prolly going into the bed. Among other things. You may have to clarify some of that terminology since I'm VERY new to airbags and whatnot. Facebook Youtube Murdered '07 Silverado
loganberry Posted July 24, 2008 Report Posted July 24, 2008 are you getting rid of the leopard (sp) on the door panels, please say yes My F-150 Build GET ON THE BANDWAGON what if they tried messing with the amps when the subs werent louder hahah jk
Tub Asko Posted July 24, 2008 Author Report Posted July 24, 2008 are you getting rid of the leopard (sp) on the door panels, please say yes most definitely. I'm gutting the interior and redoing the rat's nest that is the wiring in there. After I pull everything out I'm probably gonna spray it with e-dead. Idk yet on that. There is a lot of stuff that needs to be fixed or whatever but they are for the most part minor. The door poppers don't work because of the shoddy wiring on top of everything else. But it's a project in the making and I hope to turn it back into show quality like it once was. Facebook Youtube Murdered '07 Silverado
JMC0415 Posted July 24, 2008 Report Posted July 24, 2008 it does Nice. Good find. Can't wait to see the install for this. Keep up the sick work.
BigPimpin91 Posted July 24, 2008 Report Posted July 24, 2008 here we go (again I know about that back frame issue) 1. When this this turn to Tub's 8 12's Project?! 2. Nice to see the low rider checking out the low rider. BigPimpin91's Banging Music
Bass4Lyfe Posted July 24, 2008 Report Posted July 24, 2008 lol on tha tlast comment ~Matthew 1998 Toyota Camry XLE V6 3L (1) ScyTek Astra 4000RS-2W-1 2-Way Remote Start Alarm with Shock and Proximity (1) 20% Tint All Around (Gately Audio) (1) 250 Amperage HO Alternator (1) Big 3 Done In 1/0 (2) Kinetik HC2400 Power Cell (1) Alpine IVA-D106 Receiver (1) Peripheral Video Bypass Device (4) Alpine SPS-17C2 Speakers (1) Alpine KCE-422i iPod Control Interface (4) Sheets Dynamat Extreme; for speakers (1) 10 Square Feet Hushmat (Trunk & Rear Deck) (4) DC Audio Level 4 15" D2 Subwoofer w/ Level 5 Coils (1) Wall Built By David, Tuned to 32 Hz (1) Rockford Fosgate T40001bd Amplifier (1) Stinger 1/0 Wiring (2 runs of + 2 runs of -) (1) Stinger Volt Meter
Guest aseanj52 Posted July 24, 2008 Report Posted July 24, 2008 Tub.......I am mad at you......Ok not really...lol Can't wait to ridde in that truck again......I love the ride. We start tear down soon?
wL<3bass Posted July 24, 2008 Report Posted July 24, 2008 1. When this this turn to Tub's 8 12's Project?! 2. Nice to see the low rider checking out the low rider. LOL :rofl: :rofl: :zorro: Vehicle: 1997 S10 Blazer 4dr 4X4 Exterior: Rear End Bagged, Black Grill, Lifted 2" Amplifiers: Rockford Fosgate T8004 & T10001bd Batteries: 2 Stinger SPV35, Kinetik HC2400 Electrical: Big 3, DC Power 290amp Alternator w/ MLA at 15.5v Enclosure: 4.2 ft³ @ 33Hz 84sq.in. of port (20sq.in. per cube) Headunit: Eclipse CD3200 w/ 80G iPod Mids/Highs: Rockford T152s (a-pillars), Rockford T162s (doors) Subwoofers: 1 15" Fi BL Fully Loaded Wire: All 1/0g Kicker Hyperflex My YouTube Videos My Fiberglass A-Pillar Build My "Seamless" Looking Box Build My DD1508 T-Line Bandpass Build "Seamless" w/ Acrylic Windows (for '05 TrailBlazer) My Stealth 8" Fiberglass Build (for '05 TrailBlazer) My Build For A Friend's '08 Cobalt 15" BL Sealed Off From The Trunk My feedback/references...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.