fast85_gt Posted January 13, 2009 Report Share Posted January 13, 2009 can someone take a few minents of there time to give me a tutoral on straping 2 saz3000's @2ohm what power will i be putting to my subs also tell me how the subs are wired also all the info you can give me will help thanks Quote Link to comment Share on other sites More sharing options...
fast85_gt Posted January 13, 2009 Author Report Share Posted January 13, 2009 anyone plz Quote Link to comment Share on other sites More sharing options...
uhoh_45 Posted January 13, 2009 Report Share Posted January 13, 2009 not sure bout the saz but my powerbass you take your + from sub and run that to the + of amp A - from subs and run that to the + of amp b take both - from amp a and run that to - of amp b then put amp A in master/ Amp B in slave run your rca and your done Quote R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
fast85_gt Posted January 13, 2009 Author Report Share Posted January 13, 2009 not sure bout the saz but my powerbass you take your + from sub and run that to the + of amp A - from subs and run that to the + of amp b take both - from amp a and run that to - of amp b then put amp A in master/ Amp B in slave run your rca and your done then you just adjust the gains on the master or how does that work Quote Link to comment Share on other sites More sharing options...
Derrick824 Posted January 13, 2009 Report Share Posted January 13, 2009 Speaker wiring is the same on the Sundowns but there isn't any Master/Slave switch. Just run the Br out rca of the master amp to the Br in of the slave amp. You only have to set the master amp. The slave will automatically follow. With the pair strapped @ 2ohms they will put out 6kwatts total. Check this link for pics of strapping procedure. http://www.soundsolutionsaudio.com/forum/i...?showtopic=7406 Quote Link to comment Share on other sites More sharing options...
fast85_gt Posted January 13, 2009 Author Report Share Posted January 13, 2009 Speaker wiring is the same on the Sundowns but there isn't any Master/Slave switch. Just run the Br out rca of the master amp to the Br in of the slave amp. You only have to set the master amp. The slave will automatically follow. With the pair strapped @ 2ohms they will put out 6kwatts total. Check this link for pics of strapping procedure.http://www.soundsolutionsaudio.com/forum/i...?showtopic=7406 thanks derrick Quote Link to comment Share on other sites More sharing options...
sundownz Posted January 14, 2009 Report Share Posted January 14, 2009 Derrick is really on it regarding strapping questions today Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
Neo_frog Posted January 14, 2009 Report Share Posted January 14, 2009 On my Memphis amps, you have to buy a bridging module for the RCAs and gain match the amps prior to wiring them as listed above. There's no m/s options on them so each amp gain has to be set prior to strapping. I know you wanted to know about the SAZ, but just throwing my .02 that not all amps are the same if you ever change them out. Quote Need an install? Hit me up.[email protected]Got car audio questions? Check here first!Everything you need to know. =]http://www.stevemeadedesigns.com/board/topic/83029-everything-you-need-to-know/ Link to comment Share on other sites More sharing options...
uhoh_45 Posted January 14, 2009 Report Share Posted January 14, 2009 alot of amps that dont have br or master slave you need to use a bridging module or you can use a maxxlink i think Quote R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
Derrick824 Posted January 14, 2009 Report Share Posted January 14, 2009 alot of amps that dont have br or master slave you need to use a bridging module or you can use a maxxlink i think Correct. Most non-strappable amps can still be strapped using the Maxx-Link. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.