G_skillz81 Posted July 3, 2009 Report Share Posted July 3, 2009 Whatsup everyone, new guy here...old question though...I'm in the midst of reading up the threads on the subject (will probably have a much better idea of what's what by the end of the weekend) Anyhow, the truck is a 2003 reg cab Ram with a hard bedcover First question - where to get the accordion boot to cover the gap in the cutout between the bed and the cab? I've searched for it, but could find any place that sells them Second question - I've got 21 inches of space under the cap...most people run 12's and 15's...can i run dual 18's firing forward? (the subs are custom built 18's on a TC Sounds TC3k motor - overall diameter is 18.5) - or is this not a good idea as the cutout will be noticeably smaller? (I think 15" is the max height of the cutout I can get in there). And it will be a tight fit witht the sub jammed tight against the top and bottom plates. Not a problem to switch subs really, but I do have one of the 18's already (beating in another ride). I am limited to TC3k motors but can get them as 12's or 15's....either that, or Adire Brahmas MKIV Box design - I'd be willing to pay for a set of blueprints ..I've pm'd James with a request already, but if any one wants to take a shot at it, holla at me Quote 2003 Dodge Ram 1500 - Deep Orange Build log - Blowthrought with 4 18's http://www.stevemeadedesigns.com/board/topic/122600-4-18s-in-a-dodge-ram-team-sundown-russia/ Sundown Audio SAX125.2 - Sundown PA 10" Shok-wiring & RCA's XS Power D6500 Mechman 320A Sundown Audio Russia http://sundownaudio....dex.php?/index http://www.drive2.ru...ram/ram/skillz/ - more about my truck http://www.youtube.com/user/Gskillz81 Link to comment Share on other sites More sharing options...
97maxima Posted July 3, 2009 Report Share Posted July 3, 2009 i believe the gasket you need is sold at Rv centers . that would be one hell of a tilt on that baffle for 18s just imo id go 15s Quote American Bass*DC Power Link to comment Share on other sites More sharing options...
G_skillz81 Posted July 3, 2009 Author Report Share Posted July 3, 2009 i believe the gasket you need is sold at Rv centers . that would be one hell of a tilt on that baffle for 18s just imo id go 15s Thanks for the tip! I'm thinking I can fit them without a tilt... The MDF I'm using is close to an inch thick (I'm overseas, it's metric - 240mm. an inch is 254mm), so accounting for the top and bottom I have 19" to work with for the baffle. The only problem I potentially see is that the height of the cutout will probably be 12" max (what are the recomendations for the cut dimensions??) so that may really choke the airflow....or am I thinking too much? Quote 2003 Dodge Ram 1500 - Deep Orange Build log - Blowthrought with 4 18's http://www.stevemeadedesigns.com/board/topic/122600-4-18s-in-a-dodge-ram-team-sundown-russia/ Sundown Audio SAX125.2 - Sundown PA 10" Shok-wiring & RCA's XS Power D6500 Mechman 320A Sundown Audio Russia http://sundownaudio....dex.php?/index http://www.drive2.ru...ram/ram/skillz/ - more about my truck http://www.youtube.com/user/Gskillz81 Link to comment Share on other sites More sharing options...
G_skillz81 Posted July 5, 2009 Author Report Share Posted July 5, 2009 Guys? who else could I pm for a design for $$ on the blowthrough? I'm not getting a response from James Quote 2003 Dodge Ram 1500 - Deep Orange Build log - Blowthrought with 4 18's http://www.stevemeadedesigns.com/board/topic/122600-4-18s-in-a-dodge-ram-team-sundown-russia/ Sundown Audio SAX125.2 - Sundown PA 10" Shok-wiring & RCA's XS Power D6500 Mechman 320A Sundown Audio Russia http://sundownaudio....dex.php?/index http://www.drive2.ru...ram/ram/skillz/ - more about my truck http://www.youtube.com/user/Gskillz81 Link to comment Share on other sites More sharing options...
DHFHades Posted July 5, 2009 Report Share Posted July 5, 2009 Guys? who else could I pm for a design for $$ on the blowthrough? I'm not getting a response from James pstone11 I think is pats screen name, he does some sick blowthroughs and designs boxes...or soberbills does also I think...may wanna try them, and good luck with the build Quote 1990 Jeep Cherokee 4X4 Pioneer DEH-P2900MP, Big 3 done in 1/0, 1 run 1/0 ran to amp DAT HF1000.1 #007 powering a DC lvl4 15 DAT HR 4085 prototype powering 2 Selenium 6s and 2 no name tweeters running active 1st place in AS3 @ Surf City Sound Off, 140.8 @ 45hz @ the headrest. rebuild coming soon to get a better score "I regard the brain as a computer which will stop working when its components fail. There is no heaven of afterlife for broken down computers; that is a fairy story for people who are afraid of the dark." Link to comment Share on other sites More sharing options...
Namosh Posted July 5, 2009 Report Share Posted July 5, 2009 Here's where I got my boot seal. http://www.trucknvans.com/CRL-Slider-to-Sl...-p/ed5381rl.htm I've got an '05 Ram and if your bed is like mine, it angles away from the cab at the top. Make sure your seal will reach before you go cutting a 12" tall hole. I cut just below it starts to get wide and my cut out is only 9" tall. Quote My Ram Quad Cab Blow-through Link to comment Share on other sites More sharing options...
darrenk Posted July 5, 2009 Report Share Posted July 5, 2009 i believe mine is 11 1/2 inches tall. went from as low as i could go in the bed up to the seam below the upper brace. my vent piece opening is 11" and I have 1/4 " MDF on top and bottom with just barely any clearance Quote 2003 Dodge Ram QC 4.7, 3/5 Drop, 22's, Kenwood Excelon x792, 6x9,and 6.5, Rockford 25 to Life Power 1000, RE MX 15, Stinger 1/0 and Big 3 all soldered, Interstate Megatron +, 160A Factory Alternator, MLA Module Build Pics Link to comment Share on other sites More sharing options...
G_skillz81 Posted July 5, 2009 Author Report Share Posted July 5, 2009 Thanks for the replys guys! really appreciated!! I've sent a pm to Patrick (pstone11) hope to hear from him soon I'll try to get under the truck during the week and see what is he max cut I can get in there. When looking at it before, I found 15" between the cab's braces (that's too much for the bed though). What is the distance between the wheelwells in the Ram BTW? 2Darren - great bulid! Did the MLA module make a big difference? I'm thinking about getting one. I will also be running RF T20001bd's (one per sub) Quote 2003 Dodge Ram 1500 - Deep Orange Build log - Blowthrought with 4 18's http://www.stevemeadedesigns.com/board/topic/122600-4-18s-in-a-dodge-ram-team-sundown-russia/ Sundown Audio SAX125.2 - Sundown PA 10" Shok-wiring & RCA's XS Power D6500 Mechman 320A Sundown Audio Russia http://sundownaudio....dex.php?/index http://www.drive2.ru...ram/ram/skillz/ - more about my truck http://www.youtube.com/user/Gskillz81 Link to comment Share on other sites More sharing options...
treossi Posted July 5, 2009 Report Share Posted July 5, 2009 (edited) scroll down for accordian boots, it's like 8 bucks a foot, took me like 10 seconds to find 100 websites that sell the material http://www.pickupspecialties.com/Camper_shell_parts.htm Edited July 5, 2009 by treossi Quote Team sundownWESTCOASTSPL.COM we're throwing dbdrag events very soon visit the website for details Link to comment Share on other sites More sharing options...
darrenk Posted July 5, 2009 Report Share Posted July 5, 2009 there is 50.5" between the wheel wells my box is 49" wide and i used some 3/4" scrap pieces to keep it from shifting from side to side. The MLA works great use to drop voltage to 10v before it and now it doesnt drop below 12v. PM me if your needing a T20001 i'll be upgrading soon. Quote 2003 Dodge Ram QC 4.7, 3/5 Drop, 22's, Kenwood Excelon x792, 6x9,and 6.5, Rockford 25 to Life Power 1000, RE MX 15, Stinger 1/0 and Big 3 all soldered, Interstate Megatron +, 160A Factory Alternator, MLA Module Build Pics Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.