lem43606 Posted April 13, 2010 Report Share Posted April 13, 2010 be careful!! lol Quote 2 Fi BTL N2 18s Fully LoadedSundown Audio NS-1Kenwood 845 HU Clarion EQ4 Juicebox 3100sKnu Wire"Big 3"Mechman 270a156.3dBTeam GG. Link to comment Share on other sites More sharing options...
rc.btl Posted April 13, 2010 Author Report Share Posted April 13, 2010 i know i gotta be careful but i have to know where to cut. Quote 2004 Grand Prix HU: Alpine 9886 for sale Sub Amp:AQ2200d (possbly 2) Enclosure:BCP Designs. Best for the Money Electrical:1 Stinger SPV70 battery Subs:2 15 D2 AQ HDC coppers Wiring:0gauge power SoundQuest Wiring:0gauge ground Kicker 141.8 @ 28hz tl legal on the dash. 142.6 @ 33hz tl legal on the dash. Link to comment Share on other sites More sharing options...
Coolwazabi Posted April 13, 2010 Report Share Posted April 13, 2010 get a hair dryer... heat the cone until its pretty warm... and then get a can of "AIR", flip it upside down.. and spray.. should do the trick Quote Link to comment Share on other sites More sharing options...
rc.btl Posted April 13, 2010 Author Report Share Posted April 13, 2010 can of air??? Quote 2004 Grand Prix HU: Alpine 9886 for sale Sub Amp:AQ2200d (possbly 2) Enclosure:BCP Designs. Best for the Money Electrical:1 Stinger SPV70 battery Subs:2 15 D2 AQ HDC coppers Wiring:0gauge power SoundQuest Wiring:0gauge ground Kicker 141.8 @ 28hz tl legal on the dash. 142.6 @ 33hz tl legal on the dash. Link to comment Share on other sites More sharing options...
rc.btl Posted April 13, 2010 Author Report Share Posted April 13, 2010 so lets say i poke this tiny hole with a needle can i fill it up with air wit like a blow dryer and it'll pop out? Quote 2004 Grand Prix HU: Alpine 9886 for sale Sub Amp:AQ2200d (possbly 2) Enclosure:BCP Designs. Best for the Money Electrical:1 Stinger SPV70 battery Subs:2 15 D2 AQ HDC coppers Wiring:0gauge power SoundQuest Wiring:0gauge ground Kicker 141.8 @ 28hz tl legal on the dash. 142.6 @ 33hz tl legal on the dash. Link to comment Share on other sites More sharing options...
jdubs Posted April 13, 2010 Report Share Posted April 13, 2010 so lets say i poke this tiny hole with a needle can i fill it up with air wit like a blow dryer and it'll pop out? dude i made an account just to reply to this... lol. Dont poke holes in or ruin your stuff.. if its soft, just put a piece of duct tape on the dust cap and pull it off.. If its not THAT soft.. heat it up with a heat gun that do the duct tape thing.. Quote Kenwood DDX 514 DD M3a DD 9512G RF 600.4 RF power series 6x8s lots of zero ga. Whats coming: Kenwood Excelon screen, DD high end comps, DD 4ch, XS batteries Link to comment Share on other sites More sharing options...
chewie Posted April 13, 2010 Report Share Posted April 13, 2010 or take a long screw driver and stick it up through the pole vent and pop it back up.. Quote 91 dodge colt gt.. 4 custom t600 15s audioque 3500d.1 tuned to 25 hz... stay tuned. blazer stroker 15 brutus bxi2006d terrible voltage drop 145.4@38HZ... SEALED LEGAL Aim: chewieft09 www.t3audio.com carpe diez nuts !! my house is louder than your car... Link to comment Share on other sites More sharing options...
P4killer_ Posted April 13, 2010 Report Share Posted April 13, 2010 the duck tape works. Seen it done heat it up if its stiff. Don't stick a screwdriver up the vent it would be hard to keep it from sticking to the magnet and you might scrape the coils etc. If your going to stick anything up there use a straw and try but not a screwdriver. Duct tape first maybe a straw and if all else fails. Heat it up cut it off, fix it. Go to hobby shop for ca glue to reapply. Done Quote Setup: 2010 Hyundai Elantra Factory Unit via 4 chan NVX LOC Excessive Amperage "H/O" Alt Xs D3400/ Xs XP3000 Big 3. 2 Runs of +, 2 Runs of - DD M3b and 2 12" AQ HDC4s Link to comment Share on other sites More sharing options...
fox_racin4 Posted April 14, 2010 Report Share Posted April 14, 2010 the duck tape works. Seen it done heat it up if its stiff. Don't stick a screwdriver up the vent it would be hard to keep it from sticking to the magnet and you might scrape the coils etc. If your going to stick anything up there use a straw and try but not a screwdriver. Duct tape first maybe a straw and if all else fails. Heat it up cut it off, fix it. Go to hobby shop for ca glue to reapply. Done how will he hit the coil? get something non magnetic stick up the pole vent and push the dust cap back out or the needle trick will work just take a SMALL dab of superglue or something and cover the hole you poked will be good to go Quote 1998 gmc extd cab 12 crossfire C710s 4 SAZ-4500s 3 Singer 400A altsbuncha mids/highs Team Asshole Link to comment Share on other sites More sharing options...
rc.btl Posted April 14, 2010 Author Report Share Posted April 14, 2010 Well good new gents, dad has decided he feels bad enough he is going to buy a new one for me and he well take the old one and put that in his truck. Quote 2004 Grand Prix HU: Alpine 9886 for sale Sub Amp:AQ2200d (possbly 2) Enclosure:BCP Designs. Best for the Money Electrical:1 Stinger SPV70 battery Subs:2 15 D2 AQ HDC coppers Wiring:0gauge power SoundQuest Wiring:0gauge ground Kicker 141.8 @ 28hz tl legal on the dash. 142.6 @ 33hz tl legal on the dash. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.