Jump to content

CJ18

18+ All Access!
 View Profile  See their activity

  • Posts

    13098

  • Joined

  • Last visited

  • Days Won

    19

 Content Type 

Everything posted by CJ18

  1. CJ18

    Crescendo BC3500 on our Amp Dyno

  2. CJ18
    Part number to keep it from being too confusing in the system.
  3. CJ18
    Steve, Could you make them any thicker? The side wall of my wall is 1.5" thick and this would be an awesome way to clean up some wiring.
  4. CJ18

    YEAR END INVENTORY BLOWOUT!!!! We have a very limited quantity of DC Audio 3.5k, 5.0k, and 7.5k amplifiers left in stock that we need to move before the end of the year! Prices so LOW we cannot advertise them! Add to your cart to get the best deal of the year!!!! http://www.droppinhzcaraudio.com/santa-savings/

  5. CJ18
    Yep email sent. Gotta have one.
  6. CJ18
    Just saw this on my FB feed and had to open the computer to see it. You will have an email shortly sir.
  7. CJ18

    All DC Audio Subwoofers 15% OFF. Promo Code WOOFER15 http://www.droppinhzcaraudio.com/dc-audio/

  8. CJ18

    Crescendo Audio Amps and Speakers 15% OFF. Promo Code NENDO15 http://www.droppinhzcaraudio.com/crescendo-audio/

  9. CJ18
    More than that. If you can fit a 15" woofer, building it out that way would be to your advantage.
  10. CJ18
    If you really want a 4" coil 12" woofer, just wait until probably around April next year
  11. CJ18
    Good luck getting enough spider to allow any excursion. I know you look to have changed your mind a bit which is a good thing.Just a quick FYI, the Level 6 coil is 3.5" in diameter. It doesn't leave you with much meat on a typical 9.25" spider. The new 6 spoke basket that Fi/Crossfire came out with will accommodate a 10" spider. Look for the Crossfire XSv2 12" in a blowthrough in the near future. Incorrect. The Level 6 uses a 4" coil. To be built it would use a TC frame and 10" spider. Same spiders that are used on the 15" and 18" versions.
  12. CJ18
    There is currently not a DC 12" frame. One could possibly be custom built using the TC frame that the Level 5 12s are built with. Only thing with the Level 6 as a 12", it would have to be inverted since the motor would be wider than the basket cutout. If this is something you want to do, send me a message and I will help make it happen.
  13. CJ18
    May also want to put some weather stripping around the edges of it or something to cushion it from possibly rattling against the sides of the box.
  14. CJ18
    I looks like it would work if you just trimmed off all of the outer ring and left the small flare.
  15. CJ18
    You really should look at shrinking that box down. 1.75ft3 net would be the max I would want to see.
  16. CJ18
    i think so! That would be great. I have some ideas that would be alot easier to 3d model than they would be to just try and cut.
  17. CJ18
    I think you should be fine with them in the box. You will still have about half of the gap vent above the 1/4" part to have extra room to breathe.
  18. CJ18
    Steve, could you take a dxf file that I create and upload into your system to cut?
  19. CJ18

    Build log updated. Subs finally mounted.

    1. Show previous comments  2 more
    2. CJ18

      CJ18

      Because the lift will be powered by actuators. I did not want to do a 4 corner lift, I am worried about the stability of it if done that way with the weight that it will be lifting. Mostly worried about any sway that could potentially damage the actuators.

    3. Miguels

      Miguels

      must be your cover.. on mine i can get it to work on actuators..its a neat idea what you have going on

    4. CJ18

      CJ18

      I could easily put it on actuators to go straight up. I am planning on mounting some stuff to the under side of the tonneau. I have to be mindful of the weight and also want to do something different.

  20. CJ18
    What is the reason for the ledge in the back? Why not take the box all the way to the back? It looks like you have a couple of bolt holes drilled there, why not take it all the way back and reach through to put nuts on the bolts.
  21. CJ18
    You can still take the idea i post and move the port over to the side.
  22. CJ18
    This would be the basic idea. The dotted line represents the part that goes over the hump in the back. The part the is colored in would have be to boxed in and solid to act as the back wall of the port.
  23. CJ18
    You would have to get a little creative with the design, but I would look at doing a slot port firing forward with a dual chamber box. One sub per side and port in the middle
  24. CJ18
    With XLs you can go as small at 1.25ft3 per sub if you need to, that is one great thing about DC woofer, they dont mind being in a small box. With your amp situation and already having a Dual 2 ohm sub, best option would be to go with a pair of amps and wire strapped at 2 ohm. If you have any specific questions about any of this, please feel free to ask, I would be more than happy to help.
  25. CJ18
    Do you have the space on the side of your box for an 8" Aero?
×
×
  • Create New...