woodzyspl Posted August 1, 2011 Report Share Posted August 1, 2011 ok just asking about the 9k so hope someone has some input on how to burp with these amps. dunno if just mine but if i put on over 50% and try burp it protects. but if roll i can roll all day lol. seeing my setup right now is nothing but burps and tryna fry this xxx15 it would be easier have right volume set and just press play. once the dd1 gets here ill check gains again tho Quote AUSTRALIA do i need say more? HU: some crap pionee AMP: dc 9k @ 18v SUB: 4 elevation audio sqx 12" Battery: 2 neuton power 8200d burp setup for fun 152's soon to come: rebuilt soundstream xxx (2 18" OR 3 15" wall) Bunch speakers, more batts and new HU Link to comment Share on other sites More sharing options...
cc_audio Posted August 1, 2011 Report Share Posted August 1, 2011 Whats your voltage looking like at the amp during your burps? And why are you burping? Are you planning to compete only? I would never recommend burping such a big amp without an overkill of power behind it and only if your a big number chaser with options when it smokes. I'm just saying it would be an expensive PAIN IN THE ASS, to send that big ol amp back to the states for repair because you were playing around with it incorrectly. I'm an anti-burp guy anyway, my luck is much too bad to push my expensive amps beyond their limit. Quote It's all gone! The Celica Build Feedback If I buy something from you, DO NOT USE FEDEX! Link to comment Share on other sites More sharing options...
matt402 Posted August 1, 2011 Report Share Posted August 1, 2011 what is it wired to? how much voltage drop do u have? Quote Link to comment Share on other sites More sharing options...
woodzyspl Posted August 1, 2011 Author Report Share Posted August 1, 2011 (edited) 1ohm..voltage barley drops..2 8v batterys wired up to 16 (they do something like 5000amps over 5 seconds) it floats at about 17volts. drops down to about 16.4 lowest iv seen after 3 burps of 3 seconds each with 2 min of half volume playing tones. and yep right now just BURPS till i can get another xxx to recone to do half wall Edited August 1, 2011 by woodzyspl Quote AUSTRALIA do i need say more? HU: some crap pionee AMP: dc 9k @ 18v SUB: 4 elevation audio sqx 12" Battery: 2 neuton power 8200d burp setup for fun 152's soon to come: rebuilt soundstream xxx (2 18" OR 3 15" wall) Bunch speakers, more batts and new HU Link to comment Share on other sites More sharing options...
thehoe92 Posted August 1, 2011 Report Share Posted August 1, 2011 I have always known to roll into a burp regardless of what amp or electrical you have.. just safer on everything that way hell I roll into music just so the amp doesn't blow Quote Wouldnt be thehoe92 without teh purple Link to comment Share on other sites More sharing options...
woodzyspl Posted August 1, 2011 Author Report Share Posted August 1, 2011 oh.. good to no nvm thenn rolll FTW Quote AUSTRALIA do i need say more? HU: some crap pionee AMP: dc 9k @ 18v SUB: 4 elevation audio sqx 12" Battery: 2 neuton power 8200d burp setup for fun 152's soon to come: rebuilt soundstream xxx (2 18" OR 3 15" wall) Bunch speakers, more batts and new HU Link to comment Share on other sites More sharing options...
mhart Posted August 1, 2011 Report Share Posted August 1, 2011 i was going to say the same thing, almost all of your bigger burp systems roll into it. Burping full tilt is hard on everything. Quote '00 Honda Civic Si IASCA stock trunk/pickup 1 World Record 4/20 150.6/150.7dBTeam DC Team XS Power Team ISB Steve's Body Shophttp://www.dcsoundlab.com/ Link to comment Share on other sites More sharing options...
SS tC Posted August 2, 2011 Report Share Posted August 2, 2011 A lot of the burp systems need to "roll into it" because of being wired so low (.33,.25, and lower). The box rise helps with this and the amps end up seeing a little or a lot higher ohm load than what is metered at rest. If I play one note lower on my burp box I have to roll very slowly into it or the amp goes into protect. In the end, if you are serious about knowing the how's and why's, you need to invest in a clamp meter, 2 or more multimeters and a TL. That way you can understand and "see" what happens on each box,port,modification change you make. Quote 05 tC 6 lvl 3/4 10s RD D5 2 XSPower D1000s(16v)Thanks Scottie 2010 USACi WF SS 0-600 3rd 157.2 1 DD1508 at 2 ohms 147.5 USACi outlaw, not port Thanks for all your help Rusty Link to comment Share on other sites More sharing options...
__d_a_v_i_d__ Posted August 2, 2011 Report Share Posted August 2, 2011 1ohm..voltage barley drops..2 8v batterys wired up to 16 (they do something like 5000amps over 5 seconds) it floats at about 17volts. drops down to about 16.4 lowest iv seen after 3 burps of 3 seconds each with 2 min of half volume playing tones. and yep right now just BURPS till i can get another xxx to recone to do half wall you know i got blown xxx on deck haha... to bad u aint local... shipping shall be a BITCH lol... gonna get one back of the 5 i traded/sold Quote Chevy Impala Shocker Sigs / TC Sounds 12s Sundown NS-1 | SAX 100.4 Sundown Neos | Dayton Audio Neos ETCCC ETCCC ETCCC My YouTube ---- Subcribe!! Link to comment Share on other sites More sharing options...
woodzyspl Posted August 4, 2011 Author Report Share Posted August 4, 2011 can i haz it free? ill pay post lol i wanna half wall after seeing those level 6's..9k on 2 franken xxx/dc woofers hmm Quote AUSTRALIA do i need say more? HU: some crap pionee AMP: dc 9k @ 18v SUB: 4 elevation audio sqx 12" Battery: 2 neuton power 8200d burp setup for fun 152's soon to come: rebuilt soundstream xxx (2 18" OR 3 15" wall) Bunch speakers, more batts and new HU Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.