Winn Posted August 15, 2011 Report Share Posted August 15, 2011 Lvl 3 15 needs 3 cubes it says.. it will be on 800 watts at one ohm. Idk the common port wall thing... its just a simple slot ported box with a bend Quote You know how you avoid that? Man the fuck up and bang her best friend sister mom cousin worst enemy and never look back. JUST SAY ANTI-AUDIOPIPE Link to comment Share on other sites More sharing options...
jmilch Posted August 15, 2011 Report Share Posted August 15, 2011 (edited) If the port is using a 3 walls ie the top bottom and side, it is a 3 common wall port. Look it up, it is important to the tuning. And if I personally tune a bit lower, to around 31-32 hz, but thats just my .02 Edited August 15, 2011 by jmilch Quote Pioneer AVH-P4300DVD | Hertz 6.5 | Alpine Type R 6x9 | Custom 200A Alt | Knu Flek 1/0 Big 3 and all wiring | Eclipse EA3422 | AudioQue 2200d | DC XL 12 | Red Oak Box ~2.8 cubes @ 30 hz | Link to comment Share on other sites More sharing options...
Autruche Posted August 15, 2011 Report Share Posted August 15, 2011 I believe you would put in 4 for common port walls, as it would use a side, the back, the top, and the bottom walls as port walls. I'm not too sure though, as I don't use the Torres calculator myself. Quote Need Test Tones/Sine Waves? Click Here!My Saab 9000 build1993 Saab 9000 Aero 5spdPioneer - Zapco - Hifonics - Sundown Audio - O2 Audio - RE AudioJust Say No To Rear SpeakersJust Say No To CCA WireReal Men Drive StickHit me up on Facebook, if you want Link to comment Share on other sites More sharing options...
Winn Posted August 15, 2011 Author Report Share Posted August 15, 2011 Update for you with common port wall almost perfect Quote You know how you avoid that? Man the fuck up and bang her best friend sister mom cousin worst enemy and never look back. JUST SAY ANTI-AUDIOPIPE Link to comment Share on other sites More sharing options...
TRTC360 Posted August 15, 2011 Report Share Posted August 15, 2011 sorry for thread jacking but i'm trying to figure out how to use this properly, on the port dimensions what's the length of the port? is it the depth of the port if so, how can the port be deeper than the box itself? I probably have something wrong here but that's why i'm asking. Quote '93 Firebird Formula V8 H/U- Kenwood eXcelon KDC-X395 Mids/Highs Amp- Hifonics ZXI80.4 Wiring-KNU RCA's, Speaker Wire, And Two Runs Of Trystar 1/0 G34 Red Top and a 180amp Ford Alternator www.youtube.com/TRTC360 Link to comment Share on other sites More sharing options...
Winn Posted August 15, 2011 Author Report Share Posted August 15, 2011 I believe you would put in 4 for common port walls, as it would use a side, the back, the top, and the bottom walls as port walls. I'm not too sure though, as I don't use the Torres calculator myself. Tried 4 and it called me a silly goose Quote You know how you avoid that? Man the fuck up and bang her best friend sister mom cousin worst enemy and never look back. JUST SAY ANTI-AUDIOPIPE Link to comment Share on other sites More sharing options...
Winn Posted August 15, 2011 Author Report Share Posted August 15, 2011 (edited) sorry for thread jacking but i'm trying to figure out how to use this properly, on the port dimensions what's the length of the port? is it the depth of the port if so, how can the port be deeper than the box itself? I probably have something wrong here but that's why i'm asking. It bends like an L.. remember it the length from the point of the L to the back of the box always has to be equal the width of the port such as my depth total is 20" - .75" for wood width. then - the 3.5" inches for the width of the port which will leave you with 15.75 inches total to the back of the box and whatever way you are going.. such as for me it would go to the left 10.25" sorry if i confused you Edited August 15, 2011 by Winn Quote You know how you avoid that? Man the fuck up and bang her best friend sister mom cousin worst enemy and never look back. JUST SAY ANTI-AUDIOPIPE Link to comment Share on other sites More sharing options...
TRTC360 Posted August 15, 2011 Report Share Posted August 15, 2011 sorry for thread jacking but i'm trying to figure out how to use this properly, on the port dimensions what's the length of the port? is it the depth of the port if so, how can the port be deeper than the box itself? I probably have something wrong here but that's why i'm asking. It bends like an L.. remember it the length from the point of the L to the back of the box always has to be equal the width of the port ohh ok, see i was thinking this was a common slot port not an L-port if that's what it's called? so if it were a regular slot port the length can't be more than the depth of the box right? as you can tell i'm a n00b at this, but i'm trying to learn Quote '93 Firebird Formula V8 H/U- Kenwood eXcelon KDC-X395 Mids/Highs Amp- Hifonics ZXI80.4 Wiring-KNU RCA's, Speaker Wire, And Two Runs Of Trystar 1/0 G34 Red Top and a 180amp Ford Alternator www.youtube.com/TRTC360 Link to comment Share on other sites More sharing options...
Azagtoth502 Posted August 15, 2011 Report Share Posted August 15, 2011 Click help on the Torres calc to see the different ports...... 0 Common wall.... 1 common wall.... 2 common walls.... 3 common walls..... Quote pa-pa-platypus sorry not everybody has a companies nuts so far down their throat they catch every drop ball sweat when it falls Link to comment Share on other sites More sharing options...
Winn Posted August 15, 2011 Author Report Share Posted August 15, 2011 sorry for thread jacking but i'm trying to figure out how to use this properly, on the port dimensions what's the length of the port? is it the depth of the port if so, how can the port be deeper than the box itself? I probably have something wrong here but that's why i'm asking. It bends like an L.. remember it the length from the point of the L to the back of the box always has to be equal the width of the port ohh ok, see i was thinking this was a common slot port not an L-port if that's what it's called? so if it were a regular slot port the length can't be more than the depth of the box right? as you can tell i'm a n00b at this, but i'm trying to learn Oh i thought it was called a slot port cuz it looks like a slot LOL, We were both confused Quote You know how you avoid that? Man the fuck up and bang her best friend sister mom cousin worst enemy and never look back. JUST SAY ANTI-AUDIOPIPE Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.