AUDIOADDICT02 Posted September 23, 2011 Author Report Posted September 23, 2011 I am going to throw this out there because i just got my car out of the shop 2 days ago. I was having issues with my throttle and they said i probably needed my throttle body cleaned and if that didnt work replacing my throttle body, which would have been about $800 for my Mazda 3. But they cleaned and its running a little better now but from what I read once you get your throttle body cleaned it takes a while for the computer to get up to speed. I think in that case you'd have to clean the whole intake manifold & the maf...not sure if it works the same for the 3 as my car, but it is recommended to reset the ecu by disconnecting the negative battery terminal & holding the brake pedal for 30 secs. after doing work on the engine. Quote CHECK OUT MY MYSPACE; SOME PAINT WORK I'VE DONE: http://www.myspace.c...customcreationz DODGE RAM 1500 QUAD CAB BOX BUILD: http://www.stevemead...showtopic=48978 DODGE RAM 1500 RUMBLEBEE EDITION CUSTOM ENCLOSURE: http://www.stevemead...showtopic=48983 PREFAB REMODELING: http://www.stevemead...box-remodeling/ G35 CUSTOM PAINTED L7 BOX: http://www.stevemead...om-painted-box/ CHEVY SINGLE CAB PAINTED SUB BOX/AMP RACK: http://www.stevemead...vy-boxamp-rack/ KICKER L512 BOX BUILT TO SPECS: http://www.stevemead...-kicker-l5-box/ RF HE2 10'S KERF PORTED BOX: http://www.stevemead...erf-ported-box/ 2 DC LEVEL 3 15'S KERF ENCLOSURE: http://www.stevemeadedesigns.com/board/topic/115502-kerf-ported-enclosure/ 2 HCCA 15'S PORTED ENCLOSURE: http://www.stevemeadedesigns.com/board/topic/129468-2-hcca-15s-enclosure/
brownm3 Posted September 24, 2011 Report Posted September 24, 2011 Glad to hear ur up an running. I might try that. So while the negative battery cable is disconnected. Hold my foot on the brake for 30 secs and reconnect the cable. Might try that tomorrow. Quote BrownM3 Build Log BrownM3's Youtube Channel "Csbrown147" My Official Feedback Thread (UBL) BrownM3 Jeep Build (UBL)
AUDIOADDICT02 Posted September 24, 2011 Author Report Posted September 24, 2011 Yea pretty much, holding the brake pedal is just to drain out any current left in the car's electrical system, & leave it disconnected for a few minutes. Quote CHECK OUT MY MYSPACE; SOME PAINT WORK I'VE DONE: http://www.myspace.c...customcreationz DODGE RAM 1500 QUAD CAB BOX BUILD: http://www.stevemead...showtopic=48978 DODGE RAM 1500 RUMBLEBEE EDITION CUSTOM ENCLOSURE: http://www.stevemead...showtopic=48983 PREFAB REMODELING: http://www.stevemead...box-remodeling/ G35 CUSTOM PAINTED L7 BOX: http://www.stevemead...om-painted-box/ CHEVY SINGLE CAB PAINTED SUB BOX/AMP RACK: http://www.stevemead...vy-boxamp-rack/ KICKER L512 BOX BUILT TO SPECS: http://www.stevemead...-kicker-l5-box/ RF HE2 10'S KERF PORTED BOX: http://www.stevemead...erf-ported-box/ 2 DC LEVEL 3 15'S KERF ENCLOSURE: http://www.stevemeadedesigns.com/board/topic/115502-kerf-ported-enclosure/ 2 HCCA 15'S PORTED ENCLOSURE: http://www.stevemeadedesigns.com/board/topic/129468-2-hcca-15s-enclosure/
brownm3 Posted September 24, 2011 Report Posted September 24, 2011 Gotcha thanks or the tip. Quote BrownM3 Build Log BrownM3's Youtube Channel "Csbrown147" My Official Feedback Thread (UBL) BrownM3 Jeep Build (UBL)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.