06RTCharger Posted December 17, 2018 Author Report Share Posted December 17, 2018 Finished and smoothed panel. With my custom selfmade seat lifts lol This close edge of the panel with be mounted under the seat with the bolts going thru it. The other end doesnt reach to the other ends bolts. So this closer side will have just two lifters ontop of the panel, for a total of 1.5inches of seatlift. Then other end will have three lifters for the same total lift. Bought longer bolts too. Link to comment Share on other sites More sharing options...
06RTCharger Posted December 17, 2018 Author Report Share Posted December 17, 2018 Started tryna make a relay distribution for the remote turn on wire. Cool lookin wire thing it turned out to be lol. Everything mounted down and ready to go back into the truck. Link to comment Share on other sites More sharing options...
06RTCharger Posted December 17, 2018 Author Report Share Posted December 17, 2018 Prettied up the speaker wires. Power and remote wires prettied up too. Link to comment Share on other sites More sharing options...
06RTCharger Posted December 17, 2018 Author Report Share Posted December 17, 2018 Amps, distros and relay mounted and ready to go under seat. Tested the panel by bolting it down and it works, fits and looks great. Link to comment Share on other sites More sharing options...
06RTCharger Posted December 17, 2018 Author Report Share Posted December 17, 2018 Since i was about to have more power draw now with two amps. I wanted to make sure i fuse it uo front first. So i made a card board template then cut it out of abs, bent it with a heat gun and sanded the edges smooth becuase i used to razor and hammer technique. Score a bunch of lines where u want the cut, then hit it with a hammmer to break it off lol worked good. Link to comment Share on other sites More sharing options...
06RTCharger Posted December 17, 2018 Author Report Share Posted December 17, 2018 Fuse block mounted and wired up. I chose this location becuase the bracket i made floats right above the trucks fuse box and the bolt location allows me to rotate my smd fus block up and out of the way without removing or unbolting anything, id just have to slightly loosen the bolt that holds my bracket then it can swing/rotate upward easily. Link to comment Share on other sites More sharing options...
06RTCharger Posted December 17, 2018 Author Report Share Posted December 17, 2018 Thats it for now. I got the seats back in, they fit great. It even added a bonus mod. Now that the seat is raised, the back portion of the seat can actually fold down also. Normally these trucks dont allow the rear seat to fold down, it old folds up with the bottom portion of the seat lifting up. But now the raise caused the metal hooks on the back to be at a lerfect height so that if done correctly, when u lift the bottom seat portion the whole seat slightly lifts upward and at that point u can pull the back portion and fold it forward. Nice lil bonus i got out of this lol. Ill show it with the seats in later today, forgot to take pics of the seat back in. Its still a tight fit, i might even have to add one more set of lifters. Alright now i can sleep, post is updated! Link to comment Share on other sites More sharing options...
aburger Posted December 18, 2018 Report Share Posted December 18, 2018 Great work, super clean! Link to comment Share on other sites More sharing options...
06RTCharger Posted December 18, 2018 Author Report Share Posted December 18, 2018 On 12/17/2018 at 6:19 AM, dolarbilz said: Looks great...keep it up.very detail install. Thanks man, i try to cover as much as i can to help anyone else wanting to try to do it themselves too. Link to comment Share on other sites More sharing options...
bcbrassard Posted December 18, 2018 Report Share Posted December 18, 2018 Another kick ass build man. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.