JustinT Posted March 18, 2009 Report Share Posted March 18, 2009 I was wondering how yall would connect two runs of 8 awg to a single terminal shown below. I was thinking I could splice into the main wire coming from the amp then run it to the other terminal? Quote "IT SOUNDS SLOW MOTION AND STUTTERING"~~~~LOL 2 15" Fi BTLs 7.5 cf box @ 33hz Sundown SAZ-3500D Powermaster S3400 & D3100 Iraggi 300a alt SecondSkin - totally dead Knu wire Link to comment Share on other sites More sharing options...
uhoh_45 Posted March 18, 2009 Report Share Posted March 18, 2009 (edited) could do a number of things could put in a T from one wire to 2 out to sub or you could just run 2 wires to the amp or you could try and shove it in the terminal 0 gauge wire ran to the subs they just trimmed it down a little Edited March 18, 2009 by uhoh_45 Quote R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
JustinT Posted March 18, 2009 Author Report Share Posted March 18, 2009 Well I bought these in hopes of connecting 2 runs through the side terminals of these banana plugs. One on each side. http://www.parts-express.com/pe/showdetl.c...tnumber=091-330 Quote "IT SOUNDS SLOW MOTION AND STUTTERING"~~~~LOL 2 15" Fi BTLs 7.5 cf box @ 33hz Sundown SAZ-3500D Powermaster S3400 & D3100 Iraggi 300a alt SecondSkin - totally dead Knu wire Link to comment Share on other sites More sharing options...
JustinT Posted March 18, 2009 Author Report Share Posted March 18, 2009 and the 8 awg does not fit in the rear entry...I had to trim like 3 out of 8 twists of wire to even barely fit. Quote "IT SOUNDS SLOW MOTION AND STUTTERING"~~~~LOL 2 15" Fi BTLs 7.5 cf box @ 33hz Sundown SAZ-3500D Powermaster S3400 & D3100 Iraggi 300a alt SecondSkin - totally dead Knu wire Link to comment Share on other sites More sharing options...
rmzsuzuki89 Posted March 18, 2009 Report Share Posted March 18, 2009 (edited) could do a number of things could put in a T from one wire to 2 out to sub or you could just run 2 wires to the amp or you could try and shove it in the terminal 0 gauge wire ran to the subs they just trimmed it down a little ...What subs are these?.. And about the wiring...Just run 4 seperate 8 awg runs to the sub, then connect both positives and both negetives at the terminal (bolt) on the box. Or if you just want to run the wire through the box, just trim a little off of each. Edited March 18, 2009 by rmzsuzuki89 Quote My Feedback Thread http://www.stevemeadedesigns.com/board/topic/103868-official-rmzsuzuki89-feedback-thread/page__pid__1441542#entry1441542 Link to comment Share on other sites More sharing options...
ChevyBoy Posted March 18, 2009 Report Share Posted March 18, 2009 could do a number of things could put in a T from one wire to 2 out to sub or you could just run 2 wires to the amp or you could try and shove it in the terminal 0 gauge wire ran to the subs they just trimmed it down a little thats an understatement lol Quote Link to comment Share on other sites More sharing options...
rmzsuzuki89 Posted March 18, 2009 Report Share Posted March 18, 2009 thats an understatement lol Quite an understatement haha. Quote My Feedback Thread http://www.stevemeadedesigns.com/board/topic/103868-official-rmzsuzuki89-feedback-thread/page__pid__1441542#entry1441542 Link to comment Share on other sites More sharing options...
Audioguy564 Posted March 18, 2009 Report Share Posted March 18, 2009 :01nocomment8so: Quote Juan Rodriguez Chief Technology Officer D'Amore Engineering T15KW Support Engineer System. KVT512 Kenwood Fold Out Monitor Epic-160 Audio control Indash epicenter (1)T1500-1BD with T2000.1 Transformer 1700 watts at 2 ohms (2) T600-2 with T800-2 Transformers 320/ch at 4 ohms (2) QSD216 Q series MB Quart 6.5 inch components (3) P3D212 Rockford P3 12inch Subs (1) Very Loud Altima Coupe! Link to comment Share on other sites More sharing options...
uhoh_45 Posted March 18, 2009 Report Share Posted March 18, 2009 ...What subs are these?..And about the wiring...Just run 4 seperate 8 awg runs to the sub, then connect both positives and both negetives at the terminal (bolt) on the box. Or if you just want to run the wire through the box, just trim a little off of each. cactus sounds mk1 15-18s and for the OP if you want it to be a nice install clean and all this crap use a distro block on the outside of your box from one wire going out to 2 to the subs Quote R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
Boon Posted March 18, 2009 Report Share Posted March 18, 2009 Just strip like an inch of insulation and get 3 zip ties, let the wires unravel completely, mash them together, then zip-tie it, keep tightening the zipties for a couple of hours and they'll eventually mash together into something the size of 1 8ga. Add lots of tape Quote 10.x volts fo' life! Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.