Pretty sure I'm beating a dead horse here

[JEMT8]

How about these then if you're dead set on doing a pair of 12's.

Rockford Fosgate Punch P3D212 - $149.99 each ($299.98 for a pair plus free shipping) they would be underpowered though.

Rockford Fosgate Punch P2D412 - $99.99 each ($200 for the pair)

Or you could reach out to Mr. Flowers on here about those DC's. Level 2 or 3 12's would be good.

If I bridge down the wiring to my amp, it's capable of 900 wrms. I'm pretty sure the rms of the p3's is around 500w.

Edited December 27, 2009 by Rolladoedoe

[Alexdb7]

if you really like the p3's and your on a small budget id go with those. i use to have two in my tahoe and they were pretty nuts. great sq subs too.

[Guest]

If I bridge down the wiring to my amp, it's capable of 900 wrms. I'm pretty sure the rms of the p3's is wround 500w.

i'd look into some DC level 3's. they are a dual 2 (or 4) woofer and you can wire it to 2 ohms on your amp to get 900-ish watts to them total

[JEMT8]

if you really like the p3's and your on a small budget id go with those. i use to have two in my tahoe and they were pretty nuts. great sq subs too.

What kind of amp were you pushing them with?

[flashlight_65]

head unit- http://www.onlinecarstereo.com/CarAudio/p_...ne_CDE-102.aspx $159

amp- http://www.onlinecarstereo.com/CarAudio/p_..._BXI_2610D.aspx $358

sub- http://onlinecarstereo.com/CarAudio/p_1685..._06CVX15-2.aspx $249 or

https://ssl.perfora.net/www.ficaraudio.com/...view.shopscript $264 for the 15

rcas- http://www.darvex.com/SPI2220/Stinger+20+R...erconnects.html $12

fuses and fuse holder- http://www.darvex.com/ANL1010P/XScorpion+ANL+Fuseholder.html / http://www.darvex.com/ANLS/Sound+Quest+ANL+Fuses.html $17 (thats for 2 fuses just in case)

wire as stated above

total on the high end minus the wire $810

[JEMT8]

i'd look into some DC level 3's. they are a dual 2 (or 4) woofer and you can wire it to 2 ohms on your amp to get 900-ish watts to them total

Whats a good website to look at those at and possibly buy them from??

[Loudcivic]

this setup would get you loud for the amp you have. there d2 so you would run a 2 ohm load and a decent box and you would be suprised in how loud it will be off the amp you have.

http://cgi.ebay.com/2-RE-AUDIO-SEx12-12-SE...=item53de9203d8

[pervitizm]

Whats a good website to look at those at and possibly buy them from??

www.dcsoundlab.com

WCRusty is the owner of DC Sound Labs. You can pm or send him an email ([email protected]) and he'll get you squared away if there is no local dealer of DC subs near you.

Edited December 27, 2009 by pervitizm

[penguin3820]

i suggest you start with the electrical. like ugrading your power and ground wires this will set your foundation for any future upgrades. look into knukoceptz, shok and soundquest for wire good stuff at decent prices. dont bother with the kits make your own all you need is some ring terminals and the most inexpensive anl fuse holder you can find but be sure you get enough wire for the "big 3"

x2

[JEMT8]

www.dcsoundlab.com

WCRusty is the owner of DC Sound Labs. You can pm or send him an email ([email protected]) and he'll get you squared away if there is no local dealer of DC subs near you.

Do you have any idear how much two 12" level 3's would cost?