sundownz Posted May 5, 2010 Report Share Posted May 5, 2010 I occasionally build custom drivers on non-Sundown platforms by request -- few pictures to share These use the Z v.2 light weight 15" cone, Z v.2 production voice coils, Z v.2 production "2 spider" pack, an additional re-enforcement ring at the triple joint, stock T3 TSS frame and motor. With this cone the factory trim ring can also be used unlike the last TSS I built with the wide roll surround. * Top triple joint * Factory trim ring in place * Triple joint ring between cone and spiders. This cone is a bit shallower so there is room between the cone and spider. * The second one being built... this is my spider press rig to make sure the spiders stick well to one another and to the landing. Maybe a little overkill... but I hate to see spiders come off or apart. ----- I'll get a few more pictures before the second one is done too... will also get some specs as the customer requested them. I can actually build a couple more of these too... have a few more TSS 15" frames. Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
sundownz Posted May 5, 2010 Author Report Share Posted May 5, 2010 The frame has a non-standard landing so it was adapted with a steel ring: --- * Center support ring going into place. This locks into place around the extended neck joint on the Z v.2 spiders and is also glued into place at bottom and through it's entire height. * There is a little trough here for glue in the ring... the cone sets down into this area as well and bonds nicely. * Special rubberized surround glue. * Glue trough filled in on the ring - ready for cone to go on. * Spider press doubles as a cone press on the inside of this rig (minus the motor) to make sure the cone stays pressed into the glue trough in the ring while curing. Also used another TSS 15" to press down the trim ring to make sure the surround glue dries nicely. Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
mhart Posted May 5, 2010 Report Share Posted May 5, 2010 very nice. Quote '00 Honda Civic Si IASCA stock trunk/pickup 1 World Record 4/20 150.6/150.7dBTeam DC Team XS Power Team ISB Steve's Body Shophttp://www.dcsoundlab.com/ Link to comment Share on other sites More sharing options...
lowblueranger Posted May 6, 2010 Report Share Posted May 6, 2010 Pm me if you want to sell the other two you have -I'm interested! Quote Alpine INA-W900 Rockford Fosgate Punch 200ix Rockford Fosgate power T1500-1 Sundown SA-10 x2 Focal 6x8's front Rockford Fosgate Power T1682 rear Rockford Fosgate and Stinger Wiring Powermaster D3400, S680 Link to comment Share on other sites More sharing options...
audiogod9000 Posted May 6, 2010 Report Share Posted May 6, 2010 Lookin good bro, can't wait to see them done. PM me how much you charge for custom work, i may need my Fi updated to handle more power soon... Quote EAST TEXAS BASS HEAD 4 LIFE EAST TEXAS BASS HEAD 4 LIFE EAST TEXAS BASS HEAD 4 LIFE EAST TEXAS BASS HEAD 4 LIFE EAST TEXAS BASS HEAD 4 LIFE Jeep electronics = Stock (for now) Headunit = VR3 cheapo Speakers = Pioneer and Quantum Audio Sub Amp = Sundown SAE-1200d Sub = Fi SSD 15'' Mid/High amp = Sold my 4ch, Lookin for a new one now.... REFS: Bought From-Twistedchild420 ,J_black10,SojiaRaggs9000,hotshot27, REFS: Sold To- James , sanitarium , qu1cks1lver56, skittlesRgood Offical Audiogod9000 Feedback Audiogod9000's 1997 Jeep Cherokee Country Build Link to comment Share on other sites More sharing options...
Brandon15zzz Posted May 6, 2010 Report Share Posted May 6, 2010 Pm me a price on one if you can. Also whats the power handling on these? Quote Vehicle: 1995 Impala SSHead Unit: Pioneer AVH-P4400BHMids And Highs: (still deciding)Batteries: 1 Deka Group 34 Time to make a race car.My Build Log: Solo X 12"http://www.stevemead...don15zzz-build/My Build Log: DC lvl 4 xl 15"http://www.stevemead...don15zzz-build-My Wall Build Log: 4 Lanzar 15's/ 3k+ RMShttp://www.stevemead...t-by-techforce/My Feedback:http://www.stevemead...1 Link to comment Share on other sites More sharing options...
sundownz Posted May 6, 2010 Author Report Share Posted May 6, 2010 Should be ~1500 RMS as it is Z v.2 parts in a motor with pretty decent cooling. These are 250 + SH each. Have parts for a few more... if that many are interested I'll go count them. Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
lowblueranger Posted May 7, 2010 Report Share Posted May 7, 2010 I'll take two! Email sent. Quote Alpine INA-W900 Rockford Fosgate Punch 200ix Rockford Fosgate power T1500-1 Sundown SA-10 x2 Focal 6x8's front Rockford Fosgate Power T1682 rear Rockford Fosgate and Stinger Wiring Powermaster D3400, S680 Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.