Boon Posted September 14, 2010 Report Share Posted September 14, 2010 Impact driver. And hitting the head won't do sh!t except mess the bolt up, impact drivers don't work by vibration ;/ If the hex-head doesn't fit perfectly then make sure it's not a metric size. Depending where the woofer was made it may well be. Quote 10.x volts fo' life! Link to comment Share on other sites More sharing options...
STEvil Posted September 14, 2010 Report Share Posted September 14, 2010 2x on impact driver. Quote MickyMcD - "Capable of making some serious trouser flapping volumes at where's-my-testicles frequencies, the Servo-Drives used to be fairly jaw dropping..." Any time you have have a power wire next to your frame put some rubber hosing (or cut up an innertube) around it. The wire is bound to wiggle (due to driving or flex) and the casing will eventually wear through. Hammerdown... 1% no links to outside websites, business related FB/YT pages allowed. Link to comment Share on other sites More sharing options...
sub2weeker Posted September 14, 2010 Report Share Posted September 14, 2010 just expect the bolts to be broken when your done. they make an impact Screwdriver, handheld, and the heads will break right off.. so be prepared because you will be drilling those bitches out. or you could use acetone and let it soak and break the superglue holding the screws in. lol.. Quote this is spam imo, its not allowed here Link to comment Share on other sites More sharing options...
STEvil Posted September 14, 2010 Report Share Posted September 14, 2010 i've never broken one with an impact driver. Quote MickyMcD - "Capable of making some serious trouser flapping volumes at where's-my-testicles frequencies, the Servo-Drives used to be fairly jaw dropping..." Any time you have have a power wire next to your frame put some rubber hosing (or cut up an innertube) around it. The wire is bound to wiggle (due to driving or flex) and the casing will eventually wear through. Hammerdown... 1% no links to outside websites, business related FB/YT pages allowed. Link to comment Share on other sites More sharing options...
Rogers Posted September 14, 2010 Report Share Posted September 14, 2010 are you sure its a hex head and not a torques head? also... heat is your friend... put a good soldering iron on the head of the bolt for about a minute or so... get it good and hot, the glue should soften up enough to let it turn Quote http://www.stevemeadedesigns.com/board/topic/79921-rogers-700-dream-car-update-page-17-a-wall/?p=2335774 93 Saturn SC2My system4 SA-15's Walled 2 Cerwin-Vega S2000's 3 Kinetik Hc2000's Dual 200amp alts. you guys done with the peepee touching contest or do I need to end it? Link to comment Share on other sites More sharing options...
Slawsen Posted September 14, 2010 Author Report Share Posted September 14, 2010 (edited) Alright, thanks on all the advice guys, but I got them out finally. Now, the motor and basket still won't separate, can't even find the spot where they separate, its like 1 whole piece lol..HELP? Are they glued together? Torch doesn't seem to be working, lol. Edited September 14, 2010 by Slawsen Quote 00' Nissan Xterra Always under construction :] HU: Pioneer DEH3100-UB Mids & Highs: Kicker DS Component Set & Crescendo tweeters Mids & Highs Amp: Rockford 150.2 Subwoofer: 2 DC Audio LV 4 18"s Subwoofer Amp: Hifonics Brutus 2005d you been hanging out with jeff and dustin with that green paint? its yellow so it has to be loud. Link to comment Share on other sites More sharing options...
CHEMMINS Posted September 14, 2010 Report Share Posted September 14, 2010 Get out the camera Quote Link to comment Share on other sites More sharing options...
fritosaregood Posted September 14, 2010 Report Share Posted September 14, 2010 what kind of sub is it? there baskets are usually glued to the motor too, ive had luck with just a flat head screw driver Quote seller feedback: http://www.stevemeadedesigns.com/board/ind...showtopic=61719 http://www.stevemeadedesigns.com/board/ind...showtopic=68281 build log: http://www.stevemeadedesigns.com/board/index.php?showtopic=44800 Gf's build: http://www.stevemeadedesigns.com/board/topic/54346-kickergirls-camaro-new-box-pg-5/#entry753970 Link to comment Share on other sites More sharing options...
Loudcivic Posted September 14, 2010 Report Share Posted September 14, 2010 most baskets are glued on to the motor Quote 2015 silverado crew cab nothing atm but soon... Link to comment Share on other sites More sharing options...
Slawsen Posted September 14, 2010 Author Report Share Posted September 14, 2010 what kind of sub is it? there baskets are usually glued to the motor too, ive had luck with just a flat head screw driver 06 kicker L7 and im about to post pics, but how the hell do i get rid of the glue? acetone? pics Quote 00' Nissan Xterra Always under construction :] HU: Pioneer DEH3100-UB Mids & Highs: Kicker DS Component Set & Crescendo tweeters Mids & Highs Amp: Rockford 150.2 Subwoofer: 2 DC Audio LV 4 18"s Subwoofer Amp: Hifonics Brutus 2005d you been hanging out with jeff and dustin with that green paint? its yellow so it has to be loud. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.