sundownz Posted September 14, 2010 Report Share Posted September 14, 2010 Tooling is finally done ! * Logo embossed in the ring. The frames will have the drilled holes sealed up and all the under frame air flow will go through this ring -- brings it in right at the coil. These will show up in production toward the end of the year. Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
Skullz Posted September 14, 2010 Report Share Posted September 14, 2010 Damn thats slick and sexy looking. Quote 01 Ford focus ZX3 Pioneer AVH-X491BHS PPI PC 4800.2 Morel Maximo 6.5" x2 Link to comment Share on other sites More sharing options...
onelivinlarge Posted September 14, 2010 Report Share Posted September 14, 2010 umm sexxy Quote 1) lookj to left 2) NOTICE BLKUE 3) ME > Y9OU 4) that is all Link to comment Share on other sites More sharing options...
TeejayBee Posted September 14, 2010 Report Share Posted September 14, 2010 pshh not for 18"s ? Quote Link to comment Share on other sites More sharing options...
sundownz Posted September 14, 2010 Author Report Share Posted September 14, 2010 We don't make 18s in the SA line. Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
Eric B Posted September 14, 2010 Report Share Posted September 14, 2010 We don't make 18s in the SA line. You should! Lol Quote 2007 Chevy HHR LT UNDER CONSTRUCTION 1st Place Loud N Low 2010 MWSPL Finals 3rd Place Xtreme 3 2010 MWSPL Finals Link to comment Share on other sites More sharing options...
sundownz Posted September 14, 2010 Author Report Share Posted September 14, 2010 (edited) People seem to want them but IMO the motor is simply not strong enough... we would be talking Qts in the 0.7 to 0.8 range which is way too high, IMO, except for IB usage. Edited September 14, 2010 by sundownz Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
fritosaregood Posted September 14, 2010 Report Share Posted September 14, 2010 Are you upgrading any of the mechanical power handling too? Or is it already up to par for adding power Quote seller feedback: http://www.stevemeadedesigns.com/board/ind...showtopic=61719 http://www.stevemeadedesigns.com/board/ind...showtopic=68281 build log: http://www.stevemeadedesigns.com/board/index.php?showtopic=44800 Gf's build: http://www.stevemeadedesigns.com/board/topic/54346-kickergirls-camaro-new-box-pg-5/#entry753970 Link to comment Share on other sites More sharing options...
sundownz Posted September 14, 2010 Author Report Share Posted September 14, 2010 The suspension on the SA series is ridiculously over-built to be honest... we could clip a 1500D free air at 1 ohm and not break one mechanically. Quote - Jacob Fuller - Owner, Sundown Audio - Sundown Audio on FACEBOOK - Please DO NOT PM ME -- use my email address -- [email protected] Link to comment Share on other sites More sharing options...
CanUFeelMe Posted September 14, 2010 Report Share Posted September 14, 2010 Very nice Jacob! Can we see a pic of this on a sub? Quote 1999 Chevy S102 Sundown Zv3-10's1 Sundown saz-4500d2 sets of Sundown CS6.5 Comps. (Doors) 2 10" Sundown NeoPro 10's (Doors)1/0 KnuKonceptz - Power x2- Ground- Big 3 300 Amp External Regulated Excessive Amperage Alt 147.8 Sealed Mic on Windshiled148 30sec. Average Drivers Door open Mic on Windshield Check Out my YouTube Channel --->>> http://www.youtube.com/user/dmntyo2007?feature=guidehttp://www.stevemead...ld-competition/ Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.