Clif
18+ All Access!-
Posts
759 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Everything posted by Clif
-
What do you think? ive been lookin at it for the last hour and cant decide what i wanna do. obviously would do a t-line for either of them. just cant decide if i wanna go with less cone area with less efficiency with more power or go with more cone area, more efficency, with less power.. also would need a bigger box for the one 15. but i think the 2 tens with the higher fs would have a better all around sound. Also the 1 15 is going to be moving way more air, but idk if that will have any kind of diffrence. "An efficient speaker helps you maximize your available wattage. Believe it or not, a 3 dB increase in speaker sensitivity produces the same audible increase in volume as doubling your amplifier power. So when you're shopping for speakers, it always pays to check the sensitivity spec — especially if you have a lower-powered receiver or amp. " the tens have about a 5 db lower efficiency then the 15 has. so that right there make wattage even out. lets debate it. 10" Electrical Q Value -Qes: 0.29 Mechanical Q Value -Qms: 4.3 Total Speaker Q Value -Qts: 0.27 Free Air Resonance -Fs: 30.7 Hz Equivalent Compliance -Vas: 21.8 liters One-Way, Linear Excursion -Xmax: 22 mm Efficiency -SPL 1W/1m: 85.2 dB SPL Effective Piston Area -Sd: 310 cm^2 x 2 for 620cm^2 DC Resistance -Re: 1.9 ohm Nominal Impedance -Znom: Dual 2/4 ohm Thermal Power Handling -Pe: 1000 W Force Factor -Bl: 21 15" Electrical Q Value -Qes: 0.38 Mechanical Q Value -Qms: 4.7 Total Speaker Q Value -Qts: 0.38 Free Air Resonance -Fs: 27.8 Hz Equivalent Compliance -Vas: 126.3 liters One-Way, Linear Excursion -Xmax: 22 mm Efficiency -SPL 1W/1m: 90.4 dB SPL Effective Piston Area -Sd: 810 cm^2 DC Resistance -Re: 1.9 ohm Nominal Impedance -Znom: Dual 2/4 ohm Thermal Power Handling -Pe: 1000 W Force Factor -Bl:
-
do you still need plans?
-
lol after a nap i just noticed this myself? idk how the hell it got in here thought i put it in off topic not off topic vids.... FML.... and talkin about red navis sig
-
lol like the quote in your sig lol king of bullshitting right there.
-
i do for my test in 4.5 hours with no sleep / my field for mechanical engineer.
-
its a calculation to find out what the required flow rate of a specific coolant through a roller bearring. in other words some fun stuff.
-
Quick Question
Clif replied to Jensen's topic in General Audio - Can't find a category for your question? Ask here.
guess im going to the hardwhere store tommorw. -
yea so i got no sleep tired and its 2 here and got to be up at 7. going on day 5 doing this week.... im on number 11 and the problem is taken way to long to do and feel like taken a break.... heres where im at now. yea just procrastin cause im board and rather be on smd then doing this homeowrk and not thinken about this nonscence of a test tommorw....
-
lol
-
Quick Question
Clif replied to Jensen's topic in General Audio - Can't find a category for your question? Ask here.
use the 12s as paper waits. mix and maching 2 diffrent size subs really is not a good idea but if you yreally want to put the subs up port back in an suv usually works the best. -
The 2 Lowest Rap Songs I Know Of:
Clif replied to meade916's topic in Tunez - All things music related
deff. going to try this on the t line i see potential -
This post cannot be displayed because it is in a password protected forum. Enter Password
-
This post cannot be displayed because it is in a password protected forum. Enter Password
-
yea im also looking for some for my beer pong / drinking table keep me tuned. i almost am debating glass cuase its so dank expensive for how much i need.
-
i hope she sounds good, never made a box with them inline....
-
thats for 8, for ten of them they would not have a diagram but it would be a 1.6 ohm load Edit: Are those subs only available in 4 ohms?
-
yea like on the the baffle side my help it a bit. but dont make it to big. maybe stick out like 3 inces at the peak. also 45 that corner by the sub next to the vent i forgot to add one.
-
also note that with the subs one after the other in the line it may affect it. i never really did a box like this so you will have to let me know. Usually if i have them in line i try to make a lil chamber then put a choke in it. but this should do fine.
-
this would be right around 34 hz
-
right now the subs are on the front and the port is out the side. you can just invert it if its a problem. but to make the subs and vent out the front all you have to do is move your subs over about ten inches or so and have the vent go all the way around. it would look goofy but would work.. i will draw it up quick
-
wood is 3/4 mdf as usual. you should be able to get all your cuts off that. let me know if you need any more dims. edit: bigger pic -cliff
-
jk i got it without takin it off