jreese92 Posted April 23, 2011 Report Posted April 23, 2011 Getting a Rockford t400-4. Also I am getting the rockford t1652 components and the t1 6x9s. I want to give the 6x9s each their own channel. Then a set of components each into the other channels. How can i wire 1 set to equal a 2 ohm load into 1 channel for the amp? Quote Pioneer 6300ub Rockford Prime 6.5's Pioneer 6x9's Alpine MRP-M500 10" Alpine Type R 1.4 Cubic Foot Enclosure Tuned to 34 hz Stinger 4 Gauge Wires
MrSkippyJ Posted April 23, 2011 Report Posted April 23, 2011 you are running 4 speakers (I am counting each component set as a speaker) from a 4 channel amp with each speaker being 4 ohms. You want to know if you can each speaker up to be a 2 ohm load? If that is your question, then you can't. Quote F150: Stock 2019 Harley Road Glide: Amp: TM400Xad - 4 channel 400 watt Processor: DSR1 Fairing (Front) 6.5s -MMats PA601cx Lid (Rear) 6x9s - TMS69
RickyFriery97 Posted April 23, 2011 Report Posted April 23, 2011 If your getting 1 set of componets and 1 set of 6x9s that's 4 speakers 4 channel amp=1 speaker per channel Quote 2014 Chevy Silverado Crewcab 1994 Chevy Full Size blazer
jreese92 Posted April 23, 2011 Author Report Posted April 23, 2011 Just realized i sounded like a jackass in my post and made no sense. There will be 2 6x9s and a pair of components. But i want to put a woofer and tweeter into one channel as a 2 ohm load. is it possible? Quote Pioneer 6300ub Rockford Prime 6.5's Pioneer 6x9's Alpine MRP-M500 10" Alpine Type R 1.4 Cubic Foot Enclosure Tuned to 34 hz Stinger 4 Gauge Wires
speedball1978 Posted April 23, 2011 Report Posted April 23, 2011 a woofer and a tweeter is a component set, they will always be on one channel unless you go with a active crossover and use a seperate amp to separate them. Now to wire up 2 6x9s is possible for a 2 ohm load.. just wire them pos to pos to the amp then neg to neg then to the amp and you'll simply have a 2 ohm load. Quote
jreese92 Posted April 23, 2011 Author Report Posted April 23, 2011 a woofer and a tweeter is a component set, they will always be on one channel unless you go with a active crossover and use a seperate amp to separate them. Now to wire up 2 6x9s is possible for a 2 ohm load.. just wire them pos to pos to the amp then neg to neg then to the amp and you'll simply have a 2 ohm load. Well i can wire the T1652 comps into a 2 ohm load and how? Quote Pioneer 6300ub Rockford Prime 6.5's Pioneer 6x9's Alpine MRP-M500 10" Alpine Type R 1.4 Cubic Foot Enclosure Tuned to 34 hz Stinger 4 Gauge Wires
jreese92 Posted April 23, 2011 Author Report Posted April 23, 2011 anybody? Quote Pioneer 6300ub Rockford Prime 6.5's Pioneer 6x9's Alpine MRP-M500 10" Alpine Type R 1.4 Cubic Foot Enclosure Tuned to 34 hz Stinger 4 Gauge Wires
Sammitch0 Posted April 23, 2011 Report Posted April 23, 2011 You can't just put 4 speakers on the first 2 channels and run them 2 ohm? I'd done this before didnt know it was bad? Quote Grand Cherokee Team Backwoods Bumpers DC 15" Level 3's /w 4 Coils Pioneer deh4200ub Pioneer 3-ways Pioneer Tweeters Pioneer GM-D9500F Audiopipe 1500.1D @ 14.4v Clarion Equalizer Knuconeptz Kollosus 0ga Knuconpetz Kollosus 4ga Coming Soon: 270xp / xs1200
RickyFriery97 Posted April 23, 2011 Report Posted April 23, 2011 anybody? After the cross over pos to pos neg to neg should work Quote 2014 Chevy Silverado Crewcab 1994 Chevy Full Size blazer
MrSkippyJ Posted April 23, 2011 Report Posted April 23, 2011 Why are you bent on running the amp at 2 ohms? You would to build a new crossover to make the component set a 2 ohm load and even then I'm not sure it will work. Quote F150: Stock 2019 Harley Road Glide: Amp: TM400Xad - 4 channel 400 watt Processor: DSR1 Fairing (Front) 6.5s -MMats PA601cx Lid (Rear) 6x9s - TMS69
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.