sayhuh? Posted October 7, 2011 Report Share Posted October 7, 2011 A buddy of mine picked this up for me I got these, but are there any of these I'm missing that are a must? Also ordered the Jasper jig and should be here in a few days. Doing a nice little trunk build here soon. I may start a build thread for it. All DD Blown Link to comment Share on other sites More sharing options...
bumonskateboard6 Posted October 10, 2011 Report Share Posted October 10, 2011 I prefer to use upcut or downcut spiral bits vs the straight cut bits for hole cutouts. Other than that you're good Current Systems: 2011 BMW 335i Hertz HDP1 DC LVL3 12" Full Carbon Fiber 2002 Acura TlKenwood DNX9980HD2 DCLVL4 12" Subs with LVL5 Parts D.7 CoilsDC 3.5kHertz HSK-165 up front HCX-165 RearHertz HDP4 AmpDC Power Engineering 260 Amp AltBig 3 and amp powered with KNU 1/0XS Power D2400 Up Front i pulled out my dick in class many of times and had it shown. get over it bitch...stupid open legged hairy beavered bitch... going over rms = smaller box, under rms = bigger box... Low voltage doesn't blow amps. That's a myth. A router that does the sub holes makes rounded edges also? Link to comment Share on other sites More sharing options...
Blackedout Posted October 10, 2011 Report Share Posted October 10, 2011 Flush cut bit. Trunk Build Log Link to comment Share on other sites More sharing options...
blownengine Posted October 10, 2011 Report Share Posted October 10, 2011 Flush cut bit. ^^This. These are very useful. Also depending on how large the radius is on that roundover bit you might want some different sizes for different applications 2003 Dodge Ram 1500 SLT (Yea its got a Hemi)Alpine CDA-105KnuKonceptz 0ga CCA Big 3 with Yellow Top 15" SoundQubed HDC3DC Audio 1.2K (Bass)Pioneer 6x9's (Front)Pioneer 6.5's (Rear)Kicker 3.5's (Dash)Sony amp on the highs. (Hey it was free) Link to comment Share on other sites More sharing options...
Autruche Posted October 10, 2011 Report Share Posted October 10, 2011 Get a flushcut bit and an up cut spiral bit. I got the downcut spiral bit and I'll tell you that the upcut is for sure much better. Need Test Tones/Sine Waves? Click Here!My Saab 9000 build1993 Saab 9000 Aero 5spdPioneer - Zapco - Hifonics - Sundown Audio - O2 Audio - RE AudioJust Say No To Rear SpeakersJust Say No To CCA WireReal Men Drive StickHit me up on Facebook, if you want Link to comment Share on other sites More sharing options...
sayhuh? Posted October 10, 2011 Author Report Share Posted October 10, 2011 Thx! My jig will be here tomorrow and will put it to the test. Any particular brand for the bits? Blown Link to comment Share on other sites More sharing options...
Autruche Posted October 11, 2011 Report Share Posted October 11, 2011 I like Freud bits. CMT, Bosch, and Milwaukee are good too. You can pick up a Milwaukee upcut spiral for like 10 bucks online. Need Test Tones/Sine Waves? Click Here!My Saab 9000 build1993 Saab 9000 Aero 5spdPioneer - Zapco - Hifonics - Sundown Audio - O2 Audio - RE AudioJust Say No To Rear SpeakersJust Say No To CCA WireReal Men Drive StickHit me up on Facebook, if you want Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.