bumonskateboard6 Posted November 8, 2011 Report Posted November 8, 2011 (edited) Had some scrap MDF laying around in the garage, and my 8" DC LVL2 figured I'd play around with build a 4th order. No real plans for this other than the sake of something to do...it may end up being a test bench setup down the road if I get a battery and charger for cheap. Pictures are random cause I wasn't really planning on doing much but here ya go Sub Frame Sub mount board Port Sub in Voice coils switchable from 2 or 8 ohm so I can run it off an amp or in my house Damn warped MDF making me have to use more sealer That's all I've done for now, more updates when I've got some time. Edited November 8, 2011 by bumonskateboard6 Quote Current Systems: 2011 BMW 335i Hertz HDP1 DC LVL3 12" Full Carbon Fiber 2002 Acura TlKenwood DNX9980HD2 DCLVL4 12" Subs with LVL5 Parts D.7 CoilsDC 3.5kHertz HSK-165 up front HCX-165 RearHertz HDP4 AmpDC Power Engineering 260 Amp AltBig 3 and amp powered with KNU 1/0XS Power D2400 Up Front i pulled out my dick in class many of times and had it shown. get over it bitch...stupid open legged hairy beavered bitch... going over rms = smaller box, under rms = bigger box... Low voltage doesn't blow amps. That's a myth. A router that does the sub holes makes rounded edges also?
One Way Posted November 8, 2011 Report Posted November 8, 2011 Looks good I also wana try a 4th order with some scraps I have around but don't know the 1st thing in designing one So I gotta research a lot. Looking good tho Quote T-line build- http://www.stevemead...e-t-line-build/
Trigg Posted November 8, 2011 Report Posted November 8, 2011 Quote there is some VERY hard headed people out there. Anyone who says a DD-1 isnt necessary is also saying an O-scope isnt necessary. Anyone who says an O-scope IN THE MINIMUM isnt necessary, is a noob. Forget the DD-1 for a minute, any reputable installer will at LEAST use an O-scope. Those guys in that thread are clowns. Hard headed clowns.
fecupe2001 Posted November 8, 2011 Report Posted November 8, 2011 Very nice mate, tuned in Quote I´m the SPL Gains topic creator!! wanna get louder?? check this: SPL Gains. Panamenian 2009 & 2010 & 2014 Bass Race 149.9 Champion! 2 15" subs and a 2K wired at 1 ohm, http://www.stevemeadedesigns.com/board/topic/167788-fecupe2001-2-15s-on-a-2k-video-on-page-3/ 8 Massive 15" subs and small power, http://www.stevemeadedesigns.com/board/topic/179296-fecupe2001s-8-15s-4th-order-bandpass-wall/
Ray Posted November 8, 2011 Report Posted November 8, 2011 Fuck the box... Nice damn saw. Quote 2008 California state record holder 157.2 Bassrace2009 California state record holder 157.0 BassraceRollin 50's 158.7db2009 King of Cali Bassrace2009 USACi score 160.5 @ 42hz
fecupe2001 Posted November 8, 2011 Report Posted November 8, 2011 haha gotta love ray comments! Quote I´m the SPL Gains topic creator!! wanna get louder?? check this: SPL Gains. Panamenian 2009 & 2010 & 2014 Bass Race 149.9 Champion! 2 15" subs and a 2K wired at 1 ohm, http://www.stevemeadedesigns.com/board/topic/167788-fecupe2001-2-15s-on-a-2k-video-on-page-3/ 8 Massive 15" subs and small power, http://www.stevemeadedesigns.com/board/topic/179296-fecupe2001s-8-15s-4th-order-bandpass-wall/
baron_of_bass Posted November 8, 2011 Report Posted November 8, 2011 Ray took the words right outta my mouth. Those saws are nice! Quote Team Bass-Hz
baron_of_bass Posted November 8, 2011 Report Posted November 8, 2011 Ray took the words right outta my mouth. Those saws are nice! Quote Team Bass-Hz
bumonskateboard6 Posted November 8, 2011 Author Report Posted November 8, 2011 Looks good I also wana try a 4th order with some scraps I have around but don't know the 1st thing in designing one So I gotta research a lot. Looking good tho They aren't too difficult, just consider it a sealed box inside a ported box, gotta figure out what ratio of sealed to ported works best for your woofer, but after that it's easy. Thank you Very nice mate, tuned in Thanks! Fuck the box... Nice damn saw. Not too bad for my first table saw Ray took the words right outta my mouth. Those saws are nice! I love it, it's the reason I'm out building boxes for fun, can't just let a saw stop sit around Quote Current Systems: 2011 BMW 335i Hertz HDP1 DC LVL3 12" Full Carbon Fiber 2002 Acura TlKenwood DNX9980HD2 DCLVL4 12" Subs with LVL5 Parts D.7 CoilsDC 3.5kHertz HSK-165 up front HCX-165 RearHertz HDP4 AmpDC Power Engineering 260 Amp AltBig 3 and amp powered with KNU 1/0XS Power D2400 Up Front i pulled out my dick in class many of times and had it shown. get over it bitch...stupid open legged hairy beavered bitch... going over rms = smaller box, under rms = bigger box... Low voltage doesn't blow amps. That's a myth. A router that does the sub holes makes rounded edges also?
IH8PunkRok Posted November 8, 2011 Report Posted November 8, 2011 steel city? Quote -Matt2005 Dodge Magnum RTJVC KD-AVX1 2 PPI S580.2 Obsidian Audio ST1 Horn Tweeters PRV 8MB450s Audio Legion 3500.1D 2 RE MT 18s 360 ah LiFePO4 BatterySHCA 2/0 155.2 @ 29 hzKicker CVR 15's buildDD 3512e buildMini T-Line Build(6) 8s BuildNightshade 15s Wall BuildMagnum AB XFL 12s BuildNewest Magnum Build
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.