uhoh_45 Posted February 8, 2012 Report Share Posted February 8, 2012 just slap another dustcap overtop of that and call er a day Quote R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
IBleedMusick Posted February 8, 2012 Report Share Posted February 8, 2012 Nice for something you did in 30 mins. Quote 2013 Dodge Charger Build Log 1996 Ford Explorer XLT 5.0Build Log 2005 Honda Civic LX Coupe Build Log SMD SUPER SELLER!!!!My Selling Feedback Link to comment Share on other sites More sharing options...
CJ18 Posted February 8, 2012 Author Report Share Posted February 8, 2012 I have a much better idea about what I am doing now and how to make this work. I am going to order some more dish caps in all sizes. Quote Link to comment Share on other sites More sharing options...
Lbox88 Posted February 8, 2012 Report Share Posted February 8, 2012 Reminds me too much of T3. Sorry, had to say it. Will have to throw a big 'ole sticker on the front too see how it would look finished. Quote UBL | Build Log Link to comment Share on other sites More sharing options...
FroznBeavrBALLs Posted February 8, 2012 Report Share Posted February 8, 2012 i bet it would work good with a the cone if you had them laying around. Would look sick too. especially looking at that full Dust Cap you did there. Quote 2 DC 12" lvl 4s 1 DC 1.2k XS Power S3400 big 3 Alll KNU wire Pioneer HU cheapo Legacy coaxes (just for now) http://www.stevemead...n-sentra-build/ Link to comment Share on other sites More sharing options...
Guest Posted February 8, 2012 Report Share Posted February 8, 2012 why cant you hang it upside down to prevent that? i dont even know how that would be possible anyway haha Quote Link to comment Share on other sites More sharing options...
Watch the bass Posted February 8, 2012 Report Share Posted February 8, 2012 If you bored CJ, stay up and beget a son. Quote "in the abundance of water, the fool is thirsty" Bob Marley Link to comment Share on other sites More sharing options...
CJ18 Posted February 9, 2012 Author Report Share Posted February 9, 2012 i bet it would work good with a the cone if you had them laying around. Would look sick too. especially looking at that full Dust Cap you did there. I may give that a shot at some point. It would be completely cosmetic if I could pull it off though. why cant you hang it upside down to prevent that? i dont even know how that would be possible anyway haha If I were to hang it, the resin would drip and end up having a very ugly. bumpy finish. Quote Link to comment Share on other sites More sharing options...
CJ18 Posted February 9, 2012 Author Report Share Posted February 9, 2012 I have ordered 4 each of the full dish duatcaps, from 8-18". I have material on the way and will be starting with the 8" so that I can conserve materials while I learn and get the process down. Quote Link to comment Share on other sites More sharing options...
Trigg Posted February 9, 2012 Report Share Posted February 9, 2012 That looks like it will be pretty bad ass when you get it right! Quote there is some VERY hard headed people out there. Anyone who says a DD-1 isnt necessary is also saying an O-scope isnt necessary. Anyone who says an O-scope IN THE MINIMUM isnt necessary, is a noob. Forget the DD-1 for a minute, any reputable installer will at LEAST use an O-scope. Those guys in that thread are clowns. Hard headed clowns. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.