ZachG Posted June 3, 2012 Report Posted June 3, 2012 Ok so a week ago I installed some 1/0 kunkconceptz wire & ran it to my 2011 zx1500.1 I had to cut a few strands off to make it fit but if I move the wire at all it keeps coming out...any ideas of how to fix this????? Quote 1998 Pontiac grand prix gtp supercharged2 12" Obsidain Audio V.1 on a 2011 zx1500.1 at 2 ohms. 20ft of Knuconceptz CCA 0 Guage. 2nd Battery is a Shurken BT-120. Box is 3.5cu tuned at 31.8hz sealed off from the trunk. 14sqft of Dynamat on the Rear deck top & bottom. Soon to be more for doors/roof. Gets low & loud Did a 140.5 Sealed at Battle of the boom in June 2013 dropping to 12.7v (need a alt mines going bad)
Amart88 Posted June 3, 2012 Report Posted June 3, 2012 Ok so a week ago I installed some 1/0 kunkconceptz wire & ran it to my 2011 zx1500.1 I had to cut a few strands off to make it fit but if I move the wire at all it keeps coming out...any ideas of how to fix this????? Did you tighten the wire in the amp? it shouldn't come out. Also Knu 1/0 is closer to 2/0. Quote My 2005 s10 blazer build. 4 zcon 18's walled.
OB/GYN Kenobi Posted June 3, 2012 Report Posted June 3, 2012 Coming out of the battery terminal? Just how do you have it connected? Quote 05 Cadillac Escalade ESV Platinum Bumping the stock 9 Speaker Bose FTL... Build in progress (slow progress)
ZachG Posted June 3, 2012 Author Report Posted June 3, 2012 I tightened it as much as I could,everytime I move it it.keeps breaking off and coming out... Quote 1998 Pontiac grand prix gtp supercharged2 12" Obsidain Audio V.1 on a 2011 zx1500.1 at 2 ohms. 20ft of Knuconceptz CCA 0 Guage. 2nd Battery is a Shurken BT-120. Box is 3.5cu tuned at 31.8hz sealed off from the trunk. 14sqft of Dynamat on the Rear deck top & bottom. Soon to be more for doors/roof. Gets low & loud Did a 140.5 Sealed at Battle of the boom in June 2013 dropping to 12.7v (need a alt mines going bad)
alenv10 Posted June 3, 2012 Report Posted June 3, 2012 try to solder the end of it, so once you tighten it down, that soldered part wont be able to come out.. Quote NOTHING DOWN HERE YET OBSIDIAN FTW
Amart88 Posted June 3, 2012 Report Posted June 3, 2012 try to solder the end of it, so once you tighten it down, that soldered part wont be able to come out.. It don't matter how much he solders it. If its still loose it is not making a very good connection either way. Quote My 2005 s10 blazer build. 4 zcon 18's walled.
alenv10 Posted June 3, 2012 Report Posted June 3, 2012 well idk wat to say, hope u get a way to fix it Quote NOTHING DOWN HERE YET OBSIDIAN FTW
OrionStang Posted June 3, 2012 Report Posted June 3, 2012 OP, when you say you cut a few strands, how much did you remove? How much slack is in the wire? What do mean by "it breaks" when you wiggle the wire? Quote SMD Super Seller My Feedback Thread
HunterJohnson Posted June 3, 2012 Report Posted June 3, 2012 we need pictures to really help Quote Scion tC SQ BuildiPad mini, lots of fabrication, daily drivenFord Explorer C Pillar Wall Build Just a cheap car to destroy with bass
ZachG Posted June 3, 2012 Author Report Posted June 3, 2012 I don't know how to post pictures, & I cut like 50 off mybe....I do have a good amount of slack and my amp slides around when I drive but the connections should be more solid. I just mounted the amp to the floor hopefully that will help Quote 1998 Pontiac grand prix gtp supercharged2 12" Obsidain Audio V.1 on a 2011 zx1500.1 at 2 ohms. 20ft of Knuconceptz CCA 0 Guage. 2nd Battery is a Shurken BT-120. Box is 3.5cu tuned at 31.8hz sealed off from the trunk. 14sqft of Dynamat on the Rear deck top & bottom. Soon to be more for doors/roof. Gets low & loud Did a 140.5 Sealed at Battle of the boom in June 2013 dropping to 12.7v (need a alt mines going bad)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.