06_sierra Posted July 4, 2012 Author Report Share Posted July 4, 2012 I want to get as loud as i can with the equipment that i have. I spoke to my shop today they said if i put the mike on the drivers side it might be louder, because thats where the port is, on the drivers side. Quote Link to comment Share on other sites More sharing options...
kr15 Posted July 4, 2012 Report Share Posted July 4, 2012 mic on drivers side, passenger door open, and make sure you are not sitting in your vehicle as you could be blocking it from loading out of the open door, and you arent allowed to be in vehicle above 145 anyways. Your equipment is more then adequate. You can likely see a 46 just by tinkering around and understanding your system better. 34 is a fairly low frequency to peak at, so dont be discouraged by bigger #s at higher frequencies. Quote Team Flex Issues Low tuning > God 2011 CALI AS1 STATE CHAMP Link to comment Share on other sites More sharing options...
06_sierra Posted July 6, 2012 Author Report Share Posted July 6, 2012 well thanks everyone for their input. I will hopefully be at the fresno show to compete again. the shop i go to just got a term lab so now i have somewhere i can test run my truck at. Quote Link to comment Share on other sites More sharing options...
SPLCIVICSI Posted July 10, 2012 Report Share Posted July 10, 2012 MECA's tough with the fusing. Stinger hi-amp fuses held up the best for me if you can find them. Still would blow 2 80 amp fuses in M3 off 2 Mmats HD4000s or 1 massive D16000. They would hold 2-3 seconds on average Quote 2002 Civic Si Soundstream VR 931-NBT DLS UP36i components DC power 320 amp alt XS Power - (3) D3400s, (2) D3100s 2 DD 9515's all carbon with superchargers Audio Control MVC processor Arc Audio KS300.2 Sub amps - considering 2 T2500bdcp's for MECA M3 Link to comment Share on other sites More sharing options...
Cadillac John Posted July 18, 2012 Report Share Posted July 18, 2012 What's the lowest size fuse you think I can get away with? Will a smaller fuse result in me getting a lower score? Run some solder under a 60amp and call it good. Quote Link to comment Share on other sites More sharing options...
AA98hoe Posted July 18, 2012 Report Share Posted July 18, 2012 What's the lowest size fuse you think I can get away with? Will a smaller fuse result in me getting a lower score? Run some solder under a 60amp and call it good. This guy lol...why not just hide a copper bar there also..... pretty sure that's cheating i don't run fuses never have..thats cheating Quote TEAM DC AUDIO VEHICLE:98 chevy tahoe 2wd 3-4 drop HEADUNIT:alpine 9886 PREAMP:arcaudio FRONT STAGE:4-6 1/2s selinium,DD component set and 4-selinium tweeters in each door KICKPANELS:jl audio 5 1/4 REAR DOORS: dd components 6 1/2s HIGHS AMPS:zapco 750.2 on front doors,zapco an another 750.2 on kicks and rear doors SUBS:4-ascendant audio 18s with 5 spiders in a custom box built by KINGSUV SUB AMP: 2-dc7.5s ALTERNATORS: 3-mechmans 1- 425comp, 1-smd spec350, 1-270 with adj voltage harness on custom dc bracket WIRE:10-runs 0g front to back BATTERIES:6-d1400s TL results:157.1 at 38hz and 156.8 at headrest score @37hz. STATE AND NATIONAL RECORD IN MECA S5. Link to comment Share on other sites More sharing options...
Cadillac John Posted July 18, 2012 Report Share Posted July 18, 2012 What's the lowest size fuse you think I can get away with? Will a smaller fuse result in me getting a lower score? Run some solder under a 60amp and call it good. This guy lol...why not just hide a copper bar there also..... pretty sure that's cheating i don't run fuses never have..thats cheating Im aware. I am not guilty of this, but it is a route some take to Sand Bag a class which we all know is no better then running a lower fuse rating as well.. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.