HowLowCanYouGo Posted August 12, 2013 Report Share Posted August 12, 2013 669 watts Nothing for now... Did you get that scar tissue when you got your vagina installed? I'd grab Adam's ass and look him in the eyes for a demo of nates truck. Link to comment Share on other sites More sharing options...
Mike Whitenton Posted August 12, 2013 Report Share Posted August 12, 2013 987W Link to comment Share on other sites More sharing options...
Bass_Monster Posted August 12, 2013 Report Share Posted August 12, 2013 500 - 510 watts Link to comment Share on other sites More sharing options...
rockFord_Expedition Posted August 12, 2013 Report Share Posted August 12, 2013 (edited) guys, i am only asking for the BIGGEST number of the 3. If you post all 3 numbers, i will only accept your largest guess. Thanks! have fun, and next time, read what i write because you know, i do take time to write all that shit. You guys never pay attention. Sorry boss those directions are a little tricky I was fooled into posting 3 different numbers because of this in the OP: Certified mode (test stops @ 1% distortion) xxxx watts Non-Certified Mode (test stops @ Clipping) xxxx watts Dynamic Burst RMS (test stops @ Clipping) xxxx watts I figured you wanted us to solve for x I must be institutionalized from all these damn math classes I take plus I am half dumb more than half the time this: just give me the highest achieved number IN THE MANUFACTURER'S lowest SPECIFIED impedance. now i get it: only post one answer that you believe is the highest wattage achieved, at the manufacturers recommended lowest stable impedance. A couple questions: I am thinking the amp dyno would be an awesome tool to have at SPL competitions How are they powered? by a battery bank Could I take it from vehicle to vehicle on a cart? yes, that's what it is designed for. Watch the YouTube videos Are they warrantied? if so how long and is an extended warranty offered? I am not sure about this one, Steve or TC could answer or you could even email west coast car audio to find out Could I test a home amplifier? can't answer this for sure but its set up for dc voltage Thanks! -Sean I figured those answers would do better than nothing incase Steve doesn't reply Edited August 12, 2013 by FunkyExpedition Old School/New School RF Build March 2015 SOTM Winner How to crimp large wire Link to comment Share on other sites More sharing options...
mothra Posted August 12, 2013 Report Share Posted August 12, 2013 756, burst if nothing changes, nothing changes You don't know what you don't know, till you don't know Link to comment Share on other sites More sharing options...
Sgt Jacob Posted August 12, 2013 Report Share Posted August 12, 2013 677 Link to comment Share on other sites More sharing options...
McTw1st Posted August 12, 2013 Report Share Posted August 12, 2013 632wrms @ 4ohm Headunit: "Kenwood BT92SD" Front: "Rockford Fosgate P152S" Woofer: "Rockford Fosgate P2 4x12" Amp: "Mutant Ascension 1" RCA: "Rockford Fosgate RFIT-3" Link to comment Share on other sites More sharing options...
TigoBling Posted August 12, 2013 Report Share Posted August 12, 2013 603 2008 Sebring touring Pioneer DEH-X6500BT Stock tweets, mids, and 6x9 2 12inch Alpine SWS-12D4 Rockford Fosgate P1000XD for the subs wired at 1ohm Best Buy Flat Pack Dual 12in Box Big 3 Audio Technix 1/0 wire to Fosgate 4awg E2 disto block 1 1/0 to 2 4awg out Link to comment Share on other sites More sharing options...
walwalka Posted August 12, 2013 Report Share Posted August 12, 2013 Certified mode (test stops @ 1% distortion) 603w Non-Certified Mode (test stops @ Clipping) 627w Dynamic Burst RMS (test stops @ Clipping) 636w 2010 Honda Civic LX / Deck: Kenwood DDX371 / Front Highs: Crescendo RTS-1 / Front Mids: Silver Flute 6.5's / 4 channel: DC Audio 90.4 / Sub: Fi 15in SP4v2 / Sub amp: Taramps HD 5000 / Power wire: Knukonceptz OFC 1/0 / Deadener: Audio Technix 60 mil / Batteries: XS Power D5100R / Rear bank: TBD / Alternator: Singer 240a hairpin Link to comment Share on other sites More sharing options...
reg93f150 Posted August 12, 2013 Report Share Posted August 12, 2013 Certified mode (test stops @ 1% distortion) 729 watts Non-Certified Mode (test stops @ Clipping) 750 watts Dynamic Burst RMS (test stops @ Clipping) 780 watts ALL CREDIT TO XX1 FOR DC BANNER down rpping vanderbilt. 30 miles from victoria. i own the 3rd loudest setup here out of 3. but i did put together all 3 setups strapping 2 amps together ? like bolting them next together? using bungy cables to hold them down? or wiring separate amps to each sub Link to comment Share on other sites More sharing options...
Recommended Posts