Socky Posted October 31, 2013 Report Share Posted October 31, 2013 i think you need more port i believe i was running somewhere around 40-60 sq port in my gf's car on a single 15, 3.8 cubes tuned roughly 42, and it played from 24hz+ full tilt no probs. Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz Link to comment Share on other sites More sharing options...
Joe X Posted October 31, 2013 Report Share Posted October 31, 2013 If it ends up sounding tight to you after a while of breaking in but you still want a smaller box you can try many subs that will like that airspace better, some would be Sundown, DC, Obsidian, RF, many others.. Link to comment Share on other sites More sharing options...
BoomZoom808 Posted November 3, 2013 Author Report Share Posted November 3, 2013 Starting break in http://i1076.photobucket.com/albums/w460/808mag/C192478B-D1F7-4A17-B052-CAA3DB4BB6B7-4634-000003A4ECB0C76B_zps616eb467.mp4 2010 Mazda 3s 2.5L Pioneer DEH-X9600BHS Knu OFC 1/0 SS Platinum AGM / XS Power XP750 Alpine PDX F-4 / Morel Maximo 5 + Coax 5 IA 10.1 / SSA XCON 12 Link to comment Share on other sites More sharing options...
STEALTH808 Posted November 3, 2013 Report Share Posted November 3, 2013 For port noise I would see if you can fit in a 8" port. And if you can read through this. Flaring will help a whole lot. http://www.subwoofer-builder.com/flares-25mm.htm aero = flared TEAM SUNDOWN HAWAIIHAWAIICARAUDIO.NET 150Db Club 160Db club in the future I see krakin as a threat Link to comment Share on other sites More sharing options...
LoudBimmer Posted November 3, 2013 Report Share Posted November 3, 2013 that's a tiny port my friend. 12-16 in^2 per 1 CF is the general rule. Link to comment Share on other sites More sharing options...
ChevyBoy95 Posted November 3, 2013 Report Share Posted November 3, 2013 ignore the guy suggesting 1 4in aero. Use 1 6in Aero Port. THIS!!!! Cut it to your needed length. http://www.parts-express.com/pe/showdetl.cfm?partnumber=268-354 i would suggest 3.5 cubes with 1 6in aero at 17in long (full length). BANG! with the flare they use, you wont get port noise. And aero port rule of thumb is 9-12 sq in of port per foot. I have done lower with a load of success musically. Best Score to Date : 160.5 dB Outlaw (47Hz)[4 XM 15's & 2 Taramps Bass 12k's] BL : http://www.stevemeadedesigns.com/board/topic/147800-chevyboy95s-4-15s-7krms-wall-1533-db-on-half-power/YouTube: http://www.youtube.com/hitemwiththeflex/ Link to comment Share on other sites More sharing options...
BoomZoom808 Posted November 3, 2013 Author Report Share Posted November 3, 2013 That is the port I am using full length. 2010 Mazda 3s 2.5L Pioneer DEH-X9600BHS Knu OFC 1/0 SS Platinum AGM / XS Power XP750 Alpine PDX F-4 / Morel Maximo 5 + Coax 5 IA 10.1 / SSA XCON 12 Link to comment Share on other sites More sharing options...
BoomZoom808 Posted November 3, 2013 Author Report Share Posted November 3, 2013 2010 Mazda 3s 2.5L Pioneer DEH-X9600BHS Knu OFC 1/0 SS Platinum AGM / XS Power XP750 Alpine PDX F-4 / Morel Maximo 5 + Coax 5 IA 10.1 / SSA XCON 12 Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.