Cdizzle Posted April 26, 2007 Report Share Posted April 26, 2007 My friend is looking to build a box for a 10inch kicker L7, but he wants to put it in the trunk of his mustang... its a 86 so the trunk is like, um not there hahaha. Its a really small trunk so could someone tell me what the best way on building the box would be, I wanna make it vented... Quote Damn Thiefs Link to comment Share on other sites More sharing options...
civichatch Posted April 26, 2007 Report Share Posted April 26, 2007 My friend is looking to build a box for a 10inch kicker L7, but he wants to put it in the trunk of his mustang... its a 86 so the trunk is like, um not there hahaha. Its a really small trunk so could someone tell me what the best way on building the box would be, I wanna make it vented... Get dimensions on how much room you have to work with. You could always do sub and port facing back. Quote System Specs: Alpine SWR-1542D 15" sub Sealed Subwoofer Box MTX mxa 6001 Class D 774watts RMS @ 2ohms MTX Bass Knob Pioneer 6.5's in doors MTX Thunderdome 6x9 in rear Stinger 1 Farad capacitor 80 amp stinger fuse BIG 3 in 4 gauge wire 4 gauge power/ground wire JVC MP3 CD Car Deck (KD-G320) 12 gauge Monster speaker wire to Sub 16 gauge Stinger speaker wire to doors Stinger Gold Plated Battery Terminals Link to comment Share on other sites More sharing options...
Slinky Posted April 26, 2007 Report Share Posted April 26, 2007 kicker has some good designs in their manual check it out on their site Quote DD M4 Rockford Fosgate P500-4 SoundQubed HDC415 w carbon fiber cap 2 Rockford Fosagate T1675-S XS Power D3400 Under Hood XS Power D5100 in rear Michael Singer 200A Alt Build Log: http://www.stevemeadedesigns.com/board/topic/153901-2012-veloster-update-842013-wall-build-4-15s/ Link to comment Share on other sites More sharing options...
Cdizzle Posted April 26, 2007 Author Report Share Posted April 26, 2007 according to the guy that has talked to him, he said it was like "14 inchs high in the front 8 inchs high in the back 40ish inches w ide and like 12 inchs wide" that is the exact quote, so i dont know if that helps any... Quote Damn Thiefs Link to comment Share on other sites More sharing options...
AP Zoutes Posted April 26, 2007 Report Share Posted April 26, 2007 The hard psrt is getting the box in the trunk on those. I did one for a friend 10 yrs ago for a single 15". To get it in I took out the back seat and cut out the brace. then once everything was back in I went to local welder and had them weld it back in for me. You can fit a pretty good sized sealed box in there iirc Quote Link to comment Share on other sites More sharing options...
Chris Posted April 26, 2007 Report Share Posted April 26, 2007 The hard psrt is getting the box in the trunk on those. I did one for a friend 10 yrs ago for a single 15". To get it in I took out the back seat and cut out the brace. then once everything was back in I went to local welder and had them weld it back in for me. You can fit a pretty good sized sealed box in there iirc Actually I think the hardest part for some may be to post this thread in the correct section. Quote 4 15" FI Q D2's in 12 cubes tuned to 32hz 1- T1000.1bd's 3 Maxx 29 deep cycles 4 runs of 1/0 gauge -Big 3 -Trunk sealed off from the cabin Custom 15.8 dual-volt switching MLA module All in a CAR. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.