Thewes Posted November 3, 2009 Report Share Posted November 3, 2009 My box isn't as air tight as I would like to be and I was wondering if you all have some suggestions on what to seal the inside with? On my old enclosure I used good old silicone and it seemed to hold up okay on the MDF but it seemed to peel off on some places. Fiberglass/resin is out of the question. My new box is birch if that matters. Thanks. Quote Link to comment Share on other sites More sharing options...
ineeDBass419 Posted November 3, 2009 Report Share Posted November 3, 2009 wood glue would probly be the best Quote xbox 360 gamertag-greenrocks420 Not insulting you or anything, but did you just call us "bloody winging fairies" ? Link to comment Share on other sites More sharing options...
BassBoy69 Posted November 3, 2009 Report Share Posted November 3, 2009 I like to use wood good, and then liquid nails, the real brand, don't use the cheap kind, use gloves and then pack it around the box, give it time to cure. Quote 144+ DB'S OUT OF A CONVERTIBLE 12" Funky Pup Subwoofer (The worlds most powerful subwoofer) 6" Aero Ported Box Hifonics - Bxi2010-D Pioneer Deck RD Audio - Front Speaker Rockford Fosgate - Rear Speakers KnuKonceptz - 0 Gauge Wire KnuKonceptz SS Karma - 10 Gauge Sub Wire KnuKonceptz - Krystal Kable Rca Big 3 - Upgrade - 0 Gauge Kinetik - Hc1800 Battery Link to comment Share on other sites More sharing options...
Thewes Posted November 3, 2009 Author Report Share Posted November 3, 2009 (edited) wood glue would probly be the best Eh not exactly I went through almost 2 bottles of titebond II and it definitley holds the wood together but its not viscous enough to qualify as a sealant. I have also tried liquid nails, but its too malleable when it cures. Also a bit OT here but while I have this thread up, does anyone know the best way to clean off woofers surrounds? My 18s got a bit dusty during construction and I don't to damage the foam surrounds with chemicals. Edited November 3, 2009 by Thewes Quote Link to comment Share on other sites More sharing options...
CaptainzPlanetz Posted November 3, 2009 Report Share Posted November 3, 2009 Eh not exactly I went through almost 2 bottles of titebond II and it definitley holds the wood together but its not viscous enough to qualify as a sealant. I have also tried liquid nails, but its too malleable when it cures.Also a bit OT here but while I have this thread up, does anyone know the best way to clean off woofers surrounds? My 18s got a bit dusty during construction and I don't to damage the foam surrounds with chemicals. You could use that Duster Stuff, you know the air in a can. Quote ¿ǝɯɐƃ ǝɥʇ Trolls never learn............ All BS aside, If I see one more comment in here that is NOT about the pre-sale, I will start the vacations. And that includes the trolls feeding the trolls. YOU THE ONE THAT SOUND LIKE A OGER AND HUMPBACK/TROLLS? Add "SMDLIFER" on Xbox LIVE to play with other SMD members. Link to comment Share on other sites More sharing options...
Decaf Posted November 3, 2009 Report Share Posted November 3, 2009 (edited) ive made wood glue 45s bro... thats all u need... why does it need to be viscous? and how do u know it isnt sealed correctly? just put wood glue on the inside and outside subs are dirty whores, let them be the way they want to be, dust covered and all, lol Edited November 3, 2009 by Decaf Quote Link to comment Share on other sites More sharing options...
Boon Posted November 4, 2009 Report Share Posted November 4, 2009 Wood glue or liquid nails, just lay down a bead then put some cling film over a finger and run it along it for a real nice seal. For subs, just a very very slightly damp cloth works well for wiping them down. Quote 10.x volts fo' life! Link to comment Share on other sites More sharing options...
Nightshade Posted November 4, 2009 Report Share Posted November 4, 2009 On all my boxes I use silicone and then resin on top of that. Like the others said liquid nails will work very well and if you want to get a little more serious use PL. It is a sub flooring sealant that will never come off easily and seals pretty much anything. Quote 2013 VW Jetta GLI 2.0 Turbo 1 Sundown Audio SCV2000 1 Sundown Audio X15 V2 1 XS Power D3100 Audio Control LC6i Stock Deck 146.4 sealed on the dash at 37hz 2001 Focus ZX3: RETIRED Team Sundown Audio, Team XS Power, 2 time NSPL Car 3601-Up Champion, 2 time NSPL Car Hardcore ChampionHighest NSPL Scores to date:154.3db on the dash sealed at 46hz, 156.2db in the kick at 46hz155.2db unofficial on dash at 43hz Link to comment Share on other sites More sharing options...
wL<3bass Posted November 4, 2009 Report Share Posted November 4, 2009 I use the heavy duty liquid nails and the project liquid nails which cleans up with water....and once it cures its permanent....your main problem is your not taking your fingering and smoothing it over the sealant so it has a better bond to the wood....if you do it right you should never have a problem. The trick is to get it as flat and smooth as possible without being overly thick, that just makes it stretchy and bendable.... Quote Vehicle: 1997 S10 Blazer 4dr 4X4 Exterior: Rear End Bagged, Black Grill, Lifted 2" Amplifiers: Rockford Fosgate T8004 & T10001bd Batteries: 2 Stinger SPV35, Kinetik HC2400 Electrical: Big 3, DC Power 290amp Alternator w/ MLA at 15.5v Enclosure: 4.2 ft³ @ 33Hz 84sq.in. of port (20sq.in. per cube) Headunit: Eclipse CD3200 w/ 80G iPod Mids/Highs: Rockford T152s (a-pillars), Rockford T162s (doors) Subwoofers: 1 15" Fi BL Fully Loaded Wire: All 1/0g Kicker Hyperflex My YouTube Videos My Fiberglass A-Pillar Build My "Seamless" Looking Box Build My DD1508 T-Line Bandpass Build "Seamless" w/ Acrylic Windows (for '05 TrailBlazer) My Stealth 8" Fiberglass Build (for '05 TrailBlazer) My Build For A Friend's '08 Cobalt 15" BL Sealed Off From The Trunk My feedback/references... Link to comment Share on other sites More sharing options...
TahoeJoe Posted November 4, 2009 Report Share Posted November 4, 2009 Since fiberglass is out of the question I would use the wood glue. Glue the wood together allow cure then use a thick layer of glue on outside of joint and allow the outside glue to seal any hard to see airpockets created. Head to Lowes or home depot to pick up a small can of quality wood sealant. (usually outdoor industrial grade) over the course of a few days add 5 or 6 coats to each joint area. This will provide additional strength and keep your wood solid during heavy humidity, pressure etc. That is a cheap and easy way without fiberglass. Quote Live the dream baby...You will be shitting your pants again before you know it. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.