David711 Posted January 22, 2011 Report Posted January 22, 2011 I just bought a 98 yamaha atv without a motor and have a cbr1000 motor laying around would it be pointless to do it? Figured I could modify it and do it instead of looking for another motor for it since I haven't found one yet :/ Quote "WHOEVER SAID MONEY CAN'T BUY HAPPINESS MUST OF BEEN BROKE"
DStortz Posted January 22, 2011 Report Posted January 22, 2011 If there is a will there is a way. I have seen Motorcycles with small black 350's on them, so i would think that you could get a 1000cc motor to work in this. Quote 1978 Chevy 3/4 ton Reg Cab Pickup Alpine 9887 Imprint Head Unit JL Audio HD600.4 (Mid Amp) JL Audio HD750.1 (Sub Amp) 2 x JL 13TW5 Shallow Sub's JL C5-650 Components in fiberglassed door mod JL ZR800-CW Mid Bass in the kick panels ***UPCOMING BUILD(2 weeks and counting)*** 8 JL Audio 15" W0's in a blow through 2 Kicker 2500.1
Pitbullx Posted January 22, 2011 Report Posted January 22, 2011 its doable... I have a raptor with a hayabusa motor in it.... Quote Team Devastation Mixed Martial ArtsMachado Brazilian JiujitsuOnce I lock it on there's no escape I don't train to make you tap, I train to tear your arm, leg, or head off. Its your job to tap before I can do that -Pain is only weakness leaving the body, its kill or be killed and only the strong survive...Rockford FosgateDigital DesignsFi Car AudioCrossfire Car Audio
n8ball2013 Posted January 22, 2011 Report Posted January 22, 2011 its doable... I have a raptor with a hayabusa motor in it.... i bet that thing rips. Slightly off topic but when i was still enlisted we had these little trucks that were about the size of a larger golf cart. They were real wheel drive no weight in the ass. one person could pick them up. They were also a 1300 cc engine and governed to 25 mph. We found out if we pulled the plug on the side of the tranny case it would kill the governor. If you've never done 80 miles an hour with no power steering in a truck that two people can flip over. You havent lived. Quote THERE IS NO BUILD LOG! 1998 Chevy Silverado ext cab Alpine CDA-9887 4 Team Fi 15s 2 Ampere Audio TFE 8.0 2 Ampere Audio 150.4 3 Digital Designs CS6.5 component sets Dual Mechman 370XP Elite alternators inbound! 8 XS Power d3400 6 XS power d680 Second Skin Stinger Tsunami Wiring Sky High A Real Voltmeter not a piece of shit stinger.
David711 Posted January 22, 2011 Author Report Posted January 22, 2011 its doable... I have a raptor with a hayabusa motor in it.... I wasn't too sure and haven't looked at any of it next to eachother yet. I just figured I could make a fast 4 wheeler with what I already have instead lol Quote "WHOEVER SAID MONEY CAN'T BUY HAPPINESS MUST OF BEEN BROKE"
David711 Posted January 23, 2011 Author Report Posted January 23, 2011 Might have a change in plans. Does anybody know how much work to put a yamaha r1 motor in a yamaha raptor? Quote "WHOEVER SAID MONEY CAN'T BUY HAPPINESS MUST OF BEEN BROKE"
zayres29 Posted January 23, 2011 Report Posted January 23, 2011 it probably take the same work on either motor your still putting a 4cyl motor where a vtwin used to be you have to have pretty much all new electronics and such custom exhaust whole nine yards Quote Btw that was the first person. Ever banned by me while dropping a deuce. Feel privileged
PlugItIn Posted January 23, 2011 Report Posted January 23, 2011 it probably take the same work on either motor your still putting a 4cyl motor where a vtwin used to be you have to have pretty much all new electronics and such custom exhaust whole nine yards most likely it was a single cylinder unless it was a banshee. It is a lot of work to do something like this. Throttle cable, clutch cable, shifter, aligning everything, exhaust, motor mounts, rear end bearings, chain and sprockets/gearing, etc. But in the end, itd be worth it... Quote
David711 Posted January 23, 2011 Author Report Posted January 23, 2011 it probably take the same work on either motor your still putting a 4cyl motor where a vtwin used to be you have to have pretty much all new electronics and such custom exhaust whole nine yards most likely it was a single cylinder unless it was a banshee. It is a lot of work to do something like this. Throttle cable, clutch cable, shifter, aligning everything, exhaust, motor mounts, rear end bearings, chain and sprockets/gearing, etc. But in the end, itd be worth it... Its gonna be another money pit so I figured that I'm gonna go all out and forget the raptor motor and do something with a lot more power. Should have everything in the next week to start I can't wait! Quote "WHOEVER SAID MONEY CAN'T BUY HAPPINESS MUST OF BEEN BROKE"
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.