Jump to content

MrSkippyJ

Members
  • Posts

    10293
  • Joined

  • Last visited

  • Days Won

    22

Everything posted by MrSkippyJ

  1. but nobody here is trying to account for all the variables. the point is, all things being equal, regular mounting will be louder. there are always going to be some variables you can't account for, this is true for any testing ever done.
  2. in your experience is it always louder, or is that just louder on the TL? For someone (like me) who has zero intentions of competing does it make a difference to the ear-o-meter?
  3. you are here to clear up the bullshit this site is full of? that is a bold statement don't you think?
  4. yes, I didn't mean one clipping is good and the other is bad. My thought is this, amplifying a clipped signal is worse than an amplifier clipping a clean signal. Again, it is just a guess, seemed to make sense so I said it
  5. i have nothing to base this off of, but I think it would be worse to clip the input signal than to clip the output signal of an amplifier. I am probably wrong though.
  6. new stuff gets here 4/5!!!

  7. but my volume gets louder when i turn my gain up...
  8. how is vertically inverted any different than vertically regular as far as the mounting goes? there's not 1.5 or so inches of wood to help hold it, i'm just saying out of personal experience. but it is the same amount of wood either way. Not trying to argue with you, I am just confused
  9. how is vertically inverted any different than vertically regular as far as the mounting goes?
  10. i concede this discussion to you good sir. i truly thought there wasn't a difference though!
  11. no it won't. there is no difference between mounting a sub inverted vs. mounting it regular (assuming identical net box sizes.)
  12. if the amp stays on, my best guess is something in the signal somewhere also.
  13. does the amp stay on?
  14. play around and test out. my box turned out to be VERY peaky (it was a sealed box originally for a single JL 12 then adapted to fit a DC 12" level 2 and ported). WHen I made the trip to Ricks shop, we TL'd my set up and it peaked at about 51hz. SMall box and small port, sounds good though! Well, i'm hoping mine turns out good. mine turned out pretty well and the box wasn't even built for the sub
  15. new stuff will be here saturday...

  16. play around and test out. my box turned out to be VERY peaky (it was a sealed box originally for a single JL 12 then adapted to fit a DC 12" level 2 and ported). WHen I made the trip to Ricks shop, we TL'd my set up and it peaked at about 51hz. SMall box and small port, sounds good though!
  17. play around and test out. my box turned out to be VERY peaky (it was a sealed box originally for a single JL 12 then adapted to fit a DC 12" level 2 and ported). WHen I made the trip to Ricks shop, we TL'd my set up and it peaked at about 51hz. SMall box and small port, sounds good though!
  18. i vote troll. nobody is dumb enough to set their stuff like that AND know to mention the settings.
  19. Yes it absolutely will be fine.
  20. It's a piece of shit if it isn't 2 ohm stable.
  21. Yes, no problem at all.
  22. Forget the fuse box, just leave it as is. ADD a + wire from alt to battery, upgrade your engine block to frame and battery tonframe grounds. Edit: you can upgrade it if you want, but it has nothing to do with the charging system once you do the big 3.
  23. There seems to be some confusion as to why a 4 ohm mono and a 2 ohm stereo load are the same, as far as the amplifier is concerned. When two 4 ohm speakers are connected to each channel of a 2 channel amplifier, the amplifier is capable of driving the speakers with half of the total power supply voltage. If the amplifier has a power supply which produces plus or minus 20 volts, it will not be able to drive the speakers on a single channel with any more than 20 volts at any point in time. If we have a 2 ohm load on each channel, at the highest point on the waveform the amplifier will apply 20 volts to the speaker load. Remember that we are only considering a single point in time for this example. If we go back to ohms law... I=V/R I=20/2 I=10 amperes If we take a single 4 ohm speaker and bridge it on that same amplifier, the amplifier will be able to apply twice the voltage across the speaker. This is because while one speaker terminal is being driven positive (towards the positive rail), the other terminal is being driven towards the negative rail. This will allow the entire power supply voltage to be applied to the speaker's voice coil. It will now be able to drive the 4 ohm speaker with 40 volts instead of 20 volts in the previous example. Back to Ohm's law... I=V/R I=40/4 I=10 amperes The same amount of current flows through the output transistors whether the amplifier is driving a 4 ohm mono load or 2 ohm stereo load. As far as the amplifier is concerned, they are the same load. Taken from: http://www.bcae1.com/bridging.htm
  24. Assuming you have a mono signal going into the amp, 2 ohm stereo vs. 4 ohm mono is essentially the same thing (as far as you are using it) and you won't notice any difference.
  25. that is no joke, Rusty has answered all of my PMs (way too many if you ask me) and each time I call to order or check the status of my subs, Ana (is that correct spelling?) went all over the place checking stuff for me. I may never switch to another sub company as long as DC is around.
×
×
  • Create New...