Jump to content

MECA California suggestions/comments thread


atsaubrey

Recommended Posts

Posted

First of all. I try to run a fair and FUN show. Obviously there are some concerns about these things. 1st, I truly believe in my judges and their decisions and quality..you be hard pressed to find a better group of guys.........PERIOD! Do we mistakes? YES. We're happy to be called out on a mistake and fix it and will happily say thank you for catching it. Now, I'm trying to get keep this sport growing and I see at least in my eyes that it is. If you want be to cut off registerations at 11am sharp, then you best not be late because you've asked me to be that kind of Nazi....I know a few posts on here have been from of you "late" fellas.

Posted

This thread is getting a little hostile, everyone take step back and take a breath and remember we are all just trying to answer some questions/concerns.

Soapbox (Steve) really watch how your wording is bro, I know you are passionate about competing but, if you are going to question every judgement we make then be prepared to have you and your team under the microscope. We've been competing for over 10 years and this is only our second year with MECA and we are just like you, still learning. Alpine, as you know has just as much experience competing as Bill and myself and we truly understand about bad judgement calls at shows can cost you at finals. We are here to help as much as possible and hopefully share as much experience as we can. The dedication you and your team have shown this far in the season is great and I look forward to seeing big numbers from you guys.

Lets get some interpretations from our judges first. Rule in question is:

8. All 2 seat non-trunk vehicles: enclosure must be no higher than the bottom of the rear side glass but may not exceed

24” and must be no more than 26” from the center of the top rear door plastic panel.

This rule isn't really based around a particular vehicle but address ALL 2 seat non trunk cars which would also include some sports cars and cargo vans. In which case, I believe the measurements come into play and are voided in a CRX application. However, this is my understanding and would consult with Alpine and Bill about it ultimately letting Aubrey make the final decision.

So since he pointed out SOME judgment calls you guys made now you're going to be stricter to us than everyone else? Well that's not too fair now, is it?

And he's just pointing out some of the minor things that can easily be fixed (because there are other things we noticed, some made HUGE impacts), remember this is a suggestion/comment thread so we are allowed to make suggestions, comments, and questions.

TEAM FLEX ISSUES

Car: 1985 Oldsmobile Delta 88 Royal

24" Rims

HU: 7" Carputer, Planet Audio EQ, iPhone.

Coax: T3 Audio 4" speakers

Subs: 2x 18" T3 Audio TSNS (walled)

Sub Amp: DC 9k

SOON TO COME

T3 Audio 6x9s

MB Quarts 6.5" comp set

MAYBE ADDED

2nd DC 9k

Posted

This thread is getting a little hostile, everyone take step back and take a breath and remember we are all just trying to answer some questions/concerns.

Soapbox (Steve) really watch how your wording is bro, I know you are passionate about competing but, if you are going to question every judgement we make then be prepared to have you and your team under the microscope. We've been competing for over 10 years and this is only our second year with MECA and we are just like you, still learning. Alpine, as you know has just as much experience competing as Bill and myself and we truly understand about bad judgement calls at shows can cost you at finals. We are here to help as much as possible and hopefully share as much experience as we can. The dedication you and your team have shown this far in the season is great and I look forward to seeing big numbers from you guys.

Lets get some interpretations from our judges first. Rule in question is:

8. All 2 seat non-trunk vehicles: enclosure must be no higher than the bottom of the rear side glass but may not exceed

24” and must be no more than 26” from the center of the top rear door plastic panel.

This rule isn't really based around a particular vehicle but address ALL 2 seat non trunk cars which would also include some sports cars and cargo vans. In which case, I believe the measurements come into play and are voided in a CRX application. However, this is my understanding and would consult with Alpine and Bill about it ultimately letting Aubrey make the final decision.

So since he pointed out SOME judgment calls you guys made now you're going to be stricter to us than everyone else? Well that's not too fair now, is it?

And he's just pointing out some of the minor things that can easily be fixed (because there are other things we noticed, some made HUGE impacts), remember this is a suggestion/comment thread so we are allowed to make suggestions, comments, and questions.

SORRY SORRY SORRY SORRY.......

THIS IS EXACTLY WHAT I AM TRYING TO POINT OUT!!!!

READ MY FIRST LINE

I truly did not mean to make it seem like an attack against Soapbox (Steve) or Team Flex Issues. I was just trying to point out the Nature of the Beast. Not to mention one of the biggest things this sport is known for, Guilty by Association.

The main reason some exceptions are made are purely based on "In the Spirit of Competition". This will help grow MECA and this sport as you can see after one year. From a competitor point of view we have always built per the rule book and have asked the judge about our builds and rules. It is understandable he frustration of putting in hours of work just to see someone walk in to your class who does not belong or just showed up at 2:00 when you've been there since 8:00. However, "In the Spirit of Competition" I suggest to take the attitude of "BRING IT ON BITCH!!!".

Futhermore, I honestly was not offended by Soapbox's (Steve's) concerns about the judging, it keeps us sharp. However, exceptions will be made for certain areas of the rule for single point events based on

"In the Spirit of Competition" but, multi-pointers you can believe me we'll tighten things up.

Posted

It can be done I just got to figure out how to do it. Joseph Alt is running S4 with a ab 1100.1 in a crx and post a 155??? ish I'd have to look it up again.

Typical height in a rex is 18 max so you could use 6" of the wheel well. It's the second part that is cornfusing.

No more than 26” from the center of the top rear door plastic panel.

So does this mean the total box can't be more than 26" away from the rear loading surface?

Or does it mean you can't load to the rear of the car?

If you are limited to 26 inches away you would really be limited to 20 if you were to port back.

Or does it mean 26" from the plastic on the hatch panel this would give the competitor about 8" more than the other way.

Is the rule even fair when Hoe's can run 4 18" subs and have enclosures as big as 20 cubes? While limiting the crx to as little as 6 cubes gross not including any displacements. Will external ports be included in the measurements?

I would normally think that the 26" rule applies or starts from the tip of the extended ports to the back/rear wall or panel since the ports are still a part of the said enclosure.

TEAM S.S.C.

Team Serious SPL Centurions

df2c.jpgfzwn.jpg

Posted

here is my big issue soapbox (steve) wants more strick rules when he show up to the bakersfield show more illigal than anybody BUT he knows these rules and said oh i will fix it he even tryed to slip a slow blow fuse by me and i would of never let him run that day but was over ruled by the boss man then while running i said if someone complains we will adress it (being he was still illegal) but in the Spirit of Competition you were able to run and he comes back with oh they have to be a member do it in wrighting with a 50 dollar charge after he did some complaining never did it in wrighting nor did he pay 50 bux but steve stren was still called that day by the boss man

whats up with being a hipocret dude?

how are you trying to enforce all these rules on people which we DO then try to break them all yourself?

i did not want to make these issues with you public but i honestly feel attacked

you do know the rules! very well why dont you follow them?

Have you ever had your woofers blown?

Posted

It can be done I just got to figure out how to do it. Joseph Alt is running S4 with a ab 1100.1 in a crx and post a 155??? ish I'd have to look it up again.

Typical height in a rex is 18 max so you could use 6" of the wheel well. It's the second part that is cornfusing.

No more than 26” from the center of the top rear door plastic panel.

So does this mean the total box can't be more than 26" away from the rear loading surface?

Or does it mean you can't load to the rear of the car?

If you are limited to 26 inches away you would really be limited to 20 if you were to port back.

Or does it mean 26" from the plastic on the hatch panel this would give the competitor about 8" more than the other way.

Is the rule even fair when Hoe's can run 4 18" subs and have enclosures as big as 20 cubes? While limiting the crx to as little as 6 cubes gross not including any displacements. Will external ports be included in the measurements?

I would normally think that the 26" rule applies or starts from the tip of the extended ports to the back/rear wall or panel since the ports are still a part of the said enclosure.

im on it ron should have a break down in a few days

then we will all know what is ment by the 26 inch rule

Have you ever had your woofers blown?

Posted

wow i see some people whining about rules because they have one of the easiest cars to get loud and are still playing around in 146 land...terrible to try to accuse others of cheating due to ones own inability.

and another accusing people of cheating when they have no idea how to setup thier system so that they arent burning coils in a humongous wall that cant even break a 50....what a freekin joke.

Anyhow...any of you are free to look over Rays, Mine or Ryans builds even if your not a judge, just so we can be sure there's no cheating going on.

We are all very approachable, if you think somethings up...call us on it at the time not after all is said and done where nothing can be verified either way.

Posted

:ohsnap:

:fing23:

If I answered you in a well mannered, informative way, you asked a good question or had a good attitude. If I was an asshole, you asked a stupid question or you had a fucktard attitude... or I was in a bad mood.

Team BassickHU: Pioneer AVIC Z110Front: Peerless SLS 6.5", Peerless HDS 4", Rainbow tweeter - running activeAmp: JL HD600/4 and DC 4 channel (bridged to midbass)Processor: JBL MS-8Subs: 2x 12" AA MayhemsAmp: DC 3kElectrical: DC power 270xp alt. 1/0 big 4. XSpower D3400 and six D680s.

http://www.stevemeadedesigns.com/board/topic/121795-29-update-the-buick-is-getting-a-rebuild/

Top career scores: DBdrag 151.7 MECA SQ 82.25My SOTM build

Yeah. im pretty sure they dont warranty retarded people.

Posted

wow glad i missed a majority of the thread. my opinion is this once you get loud all the eyes are on you.It happened to me with my Rhinoliner an i fixed it and got louder lol.there is always going to be rivalry thats the nature of competeing. but i can honestly say i consider my rivals AI Ray ,and nyman my friends.i have learned from both an enjoy competing against them win or lose.as far as cheating thats going to happen its human nature for some people to try an cheat, but they will get caught.I love caraudio and competeing, if i was losing would i? yes .Id be striving to get louder and i still do. the judges are doing a fine job imo and i am friends with most, lets all stay positive and help make meca grow

TEAM DC AUDIO

VEHICLE:98 chevy tahoe 2wd 3-4 drop

HEADUNIT:alpine 9886

PREAMP:arcaudio

FRONT STAGE:4-6 1/2s selinium,DD component set and 4-selinium tweeters in each door

KICKPANELS:jl audio 5 1/4

REAR DOORS: dd components 6 1/2s

HIGHS AMPS:zapco 750.2 on front doors,zapco an another 750.2 on kicks and rear doors

SUBS:4-ascendant audio 18s with 5 spiders in a custom box built by KINGSUV

SUB AMP: 2-dc7.5s

ALTERNATORS: 3-mechmans 1- 425comp, 1-smd spec350, 1-270 with adj voltage harness on custom dc bracket

WIRE:10-runs 0g front to back

BATTERIES:6-d1400s

TL results:157.1 at 38hz and 156.8 at headrest score @37hz. STATE AND NATIONAL RECORD IN MECA S5.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Who's Online   0 Members, 0 Anonymous, 5467 Guests (See full list)

    • There are no registered users currently online
×
×
  • Create New...