dkindle613 Posted July 22, 2011 Report Share Posted July 22, 2011 so i blew my T1 15's and i am waiting to get replacements. but for the mean time, i am trying to hook up 2 12s to my T1500.1 at 2ohm like this.. but im not sure how i would hook the wires to my amp since there is 2 + and 2 - would i hook up the + on one channel of the amp, and the - to the other channel?? ooh yea, they are Sony xplods too. WARNING: I speak 4 languages, profanity, English, sarcasm & real shit 2003 ford explorer 2 RF T1 D4 15s in a 6.8 cubic ft box 1 T1500.1bdcp 250amp ALT by Mike Singer 2 runs of 0 gauge 3 yellow tops Link to comment Share on other sites More sharing options...
ChevyBoy95 Posted July 22, 2011 Report Share Posted July 22, 2011 the extra positives and negatives are for ease of wiring, just use one positive and one negative and wire the subs like shown above. Best Score to Date : 160.5 dB Outlaw (47Hz)[4 XM 15's & 2 Taramps Bass 12k's] BL : http://www.stevemeadedesigns.com/board/topic/147800-chevyboy95s-4-15s-7krms-wall-1533-db-on-half-power/YouTube: http://www.youtube.com/hitemwiththeflex/ Link to comment Share on other sites More sharing options...
Socky Posted July 22, 2011 Report Share Posted July 22, 2011 Just hook the subwoofers directly to the amp, its a mono amp (1 channel) when hooking the two 4 ohm subwoofers to it, the amp will see a 2 ohm load. Or just wire them like above. Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz Link to comment Share on other sites More sharing options...
dkindle613 Posted July 22, 2011 Author Report Share Posted July 22, 2011 Just hook the subwoofers directly to the amp, its a mono amp (1 channel) when hooking the two 4 ohm subwoofers to it, the amp will see a 2 ohm load. Or just wire them like above. even if the subs are single voice coil? just hook one sub to each channel, and call it a day? WARNING: I speak 4 languages, profanity, English, sarcasm & real shit 2003 ford explorer 2 RF T1 D4 15s in a 6.8 cubic ft box 1 T1500.1bdcp 250amp ALT by Mike Singer 2 runs of 0 gauge 3 yellow tops Link to comment Share on other sites More sharing options...
Torres Posted July 22, 2011 Report Share Posted July 22, 2011 yes. a mono amp has multiple terminals,not have multiple channels. this seems to confuse so many people. they come together inside the amp. so wire it just like above either in each terminal, or in one terminal. makes no difference Link to comment Share on other sites More sharing options...
dkindle613 Posted July 22, 2011 Author Report Share Posted July 22, 2011 alright. thanks a lot guys WARNING: I speak 4 languages, profanity, English, sarcasm & real shit 2003 ford explorer 2 RF T1 D4 15s in a 6.8 cubic ft box 1 T1500.1bdcp 250amp ALT by Mike Singer 2 runs of 0 gauge 3 yellow tops Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.