KenC210 Posted September 30, 2011 Report Share Posted September 30, 2011 so i want to make sure i am right on this... So if i wire 2 speakers together (in parallel) that handle 100wrms each i do still run about 100wrms or am i able to run 200wrms? sorry for the noob question just wanna make sure that way i dont purchase an amp to large Quote Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
woodzyspl Posted September 30, 2011 Report Share Posted September 30, 2011 200rms. 100+100=200 Quote AUSTRALIA do i need say more? HU: some crap pionee AMP: dc 9k @ 18v SUB: 4 elevation audio sqx 12" Battery: 2 neuton power 8200d burp setup for fun 152's soon to come: rebuilt soundstream xxx (2 18" OR 3 15" wall) Bunch speakers, more batts and new HU Link to comment Share on other sites More sharing options...
KenC210 Posted September 30, 2011 Author Report Share Posted September 30, 2011 Ok so i answered my own question with some other research... http://www.usspeaker.com/speaker%20wiring-1.htm Parallel Wiring - Speakers of equal impedances you divide the impedance value by the number of speakers. To determine the wattage you add the wattage of the speakers together. If you wire (4) 16 ohm speakers in parallel you'd have a 4 ohm cabinet. (2) 16 ohm speakers in parallel would give you an 8 ohm cabinet. If you were using (4) 100 watts speakers you'd have 400 watts power handling. If you were using (2) 100 watt speakers you'd have 200 watts power handling. So know what i need help with is if i have 4 speakers and 2 are 150wrms and the other 2 are 100wrms would i be able to run 500wrms if they were all the same ohm load and wired in parallel to have a 2ohm load then wired into a mono amp? sorry if its confusing i just would like to do things right. Quote Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
CHEVY4X4BLAZER Posted September 30, 2011 Report Share Posted September 30, 2011 (edited) I believe Wattage is equally distributed to all the speakers on that channel. You might over power the 100 rms woofers and burn the coils. . Edited September 30, 2011 by CHEVY4X4BLAZER Quote Link to comment Share on other sites More sharing options...
KenC210 Posted September 30, 2011 Author Report Share Posted September 30, 2011 This is more of an example of what i am trying to do. So now i know there is a total of 500wrms. Would i be able to wire it something like this? Could i do the 500wrms or should i do 400wrms? Any suggestions? Also if i use a bass blocker that blocks 0-400hz @ 4ohm's would i see it to block 0-200hz @ 8ohm's or 0-800hz @ 2ohm's? I may be making this more difficult than it really is but i just want to get this right. Quote Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
Lbox88 Posted September 30, 2011 Report Share Posted September 30, 2011 400W. If you gave them the full 500W, then each speaker would be seeing 125W since they are all the same impedance and the power is equally distributed across all loads. Quote UBL | Build Log Link to comment Share on other sites More sharing options...
CHEVY4X4BLAZER Posted September 30, 2011 Report Share Posted September 30, 2011 Is your amp 1 ohm stable? 4 SVC 4ohm speakers wired parallel results in a 1 ohm load. Quote Link to comment Share on other sites More sharing options...
CleanSierra Posted September 30, 2011 Report Share Posted September 30, 2011 Is your amp 1 ohm stable? 4 SVC 4ohm speakers wired parallel results in a 1 ohm load. Not to mention a mono amp is for bass. The response will not go much above 250 Hz. No sound will come out of those speakers if it's a class D mono amp. Quote Im not the one you want to try to troll. Just a fyi for you. Link to comment Share on other sites More sharing options...
KenC210 Posted September 30, 2011 Author Report Share Posted September 30, 2011 (edited) i have been looking around and i have seen some amps to allow the frequency response to be 20-20000hz http://www.audiosavings.com/products/Mono-Car-Amplifier/Rockford-Fosgate-P400-1-Punch-Series-400-Watt-RMS-Mono-Block-Amplifier-Car-Amp/P400-1.aspx just as an example. This is why i was wondering. also if i was to use a 2 channel amp and get 4 tweeters that are capable of handling 70wrms and i get 4 of them and each one is 8ohm load and wired together for a 4ohm load and they are in each channel and i have the midbass bridged how would that work? edit: also what about the little capacitors on the tweeters how would they work in this situation? Also if i use a bass blocker that blocks 0-400hz @ 4ohm's would i see it to block 0-200hz @ 8ohm's or 0-800hz @ 2ohm's? Edited September 30, 2011 by KenC210 Quote Kids Cadi Power Wheel Build2007 Ford Escape Build2012 Toyota Corolla Build 2013 Toyota Tundra Link to comment Share on other sites More sharing options...
Stephen_og Posted September 30, 2011 Report Share Posted September 30, 2011 (edited) IIRC, if you wire two speakers in parallel, you dont increase the RMS of the speaker, the ohm load to the amp increases the wattage that goes to the said speakers.. If i missed that some one already said that, my bad.. just trying to lend some helpful advice. Edited September 30, 2011 by Stephen_og Quote Team NWSPLUPCOMING BUILD (when I afford it) 2013 Ford Focus Hatch 2x DC lv3 15s 2x b2 quotas XS batts DC power alt That amp would fuck the shit out of those subs. It would roofie them, knock them out with chloroform, then make sweet, gentle, anal love to them all night. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.