carshateme Posted December 9, 2011 Report Posted December 9, 2011 What's your opinions, Box is tuned at 28 hz, as asked of by a friend. Braces are 2x2s Dimension is 52.5x18.5x31 Port Dim. is 36x2.5x15.5 New build coming soon. [center][url="http://imageshack.us/photo/my-images/3/sigtoo.jpg/"][img]http://img3.imageshack.us/img3/9541/sigtoo.jpg[/img][/url][/center]
bassrace Posted December 9, 2011 Report Posted December 9, 2011 8 10"s? What subs? What's the specs on the box? 145.9@40hz 145.3@34hz big 3 X2 group 34 Deka Group 31 All 0/1 awg jl meta wire Alpine CDA 7894 Orion HCCA D5000 2 AQ HDC312's Crunch gpv1100.2 (for 6.5"s only) AQ pro audio 6.5" - 3 sets AQ supertweeters - 2 sets 2000 Slamry
412 CVX Posted December 9, 2011 Report Posted December 9, 2011 i think the port is too short. IIRC a 1:6 ratio of height to width is a good rule of thumb. Just say no to Ground Pounder Customs. My temp system build log More box buildssome cars do over 170db with one sub, so clearly my two 12"s can do that in my car, with my knowledge too! look out bitches! I'm with captain stupid.
6berry Posted December 9, 2011 Report Posted December 9, 2011 that port might be a little too thin but other than that it looks good. 1999 Audi A4 1.8T::: 4 - DC Level 3 10's in a 4th order Rockford P6002 on Subs for now (3-3.5k coming eventually) MB Quart ONX4.60 for Mids and Highs Boston S50 Components in Front Boston S65 Coaxials in Rear 40 Sq Ft of Second Skin Damplifier Build Thread UBL 1948 Plymouth
Socky Posted December 9, 2011 Report Posted December 9, 2011 I think the power is a little narrow, make it taller and not as wide might sound a little better too. Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz
carshateme Posted December 9, 2011 Author Report Posted December 9, 2011 So what's the ideal port length you're suggesting...because I am thinking about 4" for the height.. New build coming soon. [center][url="http://imageshack.us/photo/my-images/3/sigtoo.jpg/"][img]http://img3.imageshack.us/img3/9541/sigtoo.jpg[/img][/url][/center]
bassrace Posted December 9, 2011 Report Posted December 9, 2011 Is it in the 12-16 sq in of port per cu ft range? 145.9@40hz 145.3@34hz big 3 X2 group 34 Deka Group 31 All 0/1 awg jl meta wire Alpine CDA 7894 Orion HCCA D5000 2 AQ HDC312's Crunch gpv1100.2 (for 6.5"s only) AQ pro audio 6.5" - 3 sets AQ supertweeters - 2 sets 2000 Slamry
412 CVX Posted December 9, 2011 Report Posted December 9, 2011 So what's the ideal port length you're suggesting...because I am thinking about 4" for the height.. Like i said earlier, about a 1:6 ratio. so if you're going to do 4" high, about 24" wide, give or take would be ideal. Just say no to Ground Pounder Customs. My temp system build log More box buildssome cars do over 170db with one sub, so clearly my two 12"s can do that in my car, with my knowledge too! look out bitches! I'm with captain stupid.
Recommended Posts
Archived
This topic is now archived and is closed to further replies.