Trey_Dog650 Posted October 2, 2012 Report Share Posted October 2, 2012 Yeah I hear yuh man. Im in the same boat 13 Kia Forte Build! 07 Hyundai Accent Build ***Super Seller*** N8ball2013 And then he gets to say ok all you guys were right. im sorry for being a dummy poo poo head. Link to comment Share on other sites More sharing options...
sprkn_ranger Posted October 2, 2012 Report Share Posted October 2, 2012 Infinite baffle, nice! What amp are you gonna power them with? Should turn out real good. Check out my build log! 4 Havocs in a blowthrough http://www.stevemeadedesigns.com/board/topic/187506-sprkn-rangers-blowthrough-build/ Link to comment Share on other sites More sharing options...
OrionStang Posted October 2, 2012 Author Report Share Posted October 2, 2012 Infinite baffle, nice! What amp are you gonna power them with? Should turn out real good. The rear channels of the 200.4. The subs are only 250rms each. And I hope it turns out. As far as engine mods, i've decided to do the intake manifold, cams, and pulley swap. Just need the shop to open up some time for me. Also got a new CAI on the way, from C&L. Supposed to flow better than Steeda. SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
OrionStang Posted October 7, 2012 Author Report Share Posted October 7, 2012 Finally had time to do a little figuring of the baffle. SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
OrionStang Posted October 7, 2012 Author Report Share Posted October 7, 2012 I also hope to replace all my speaker wire tomorrow morning with 150' of Kicker 14awg, if my hangover isn't too bad. Still need to decide on the trunk configuration. The amp and crossovers will be back there and the floor will be vinyl, just have to figure how to hide the wires. SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
Blue Posted October 7, 2012 Report Share Posted October 7, 2012 Looking nice. For wire hiding, put the amp board and crossovers on a raised platform and drill jokes in the platform and run the wires under the board the there respected locations formerly known as Blue86f150 its a 4th order just because its tuned in the 40z doesnt mean it wont reach down and jiggle your balls at sub 30 hz frequencies. Regardless if they were dipped platinum and were stuffed in Beyonce's twat.....way too fucking exspensive this sux camel dicks Link to comment Share on other sites More sharing options...
OrionStang Posted October 10, 2012 Author Report Share Posted October 10, 2012 Alright, I haven't done shit with the IB, been busy with 'life' LOL. But, on the performance end, my CAI will be here tonight, and my camshafts (and phase bolts) and intake manifold shipped this afternoon. Spankin' Time Motorsports in San Bernardino will be doing the install and dyno tuning once all my parts are in. Stoked is an understatement. SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
Audio-Concepts Posted October 11, 2012 Report Share Posted October 11, 2012 Im going to guess 490-500 whp after tuning! Pioneer AVH480 Zapco ST5XII amplifier Stevens Audio 6.5" components (passive) Onyx Subwoofer Sky High OFC wiring Link to comment Share on other sites More sharing options...
OrionStang Posted October 11, 2012 Author Report Share Posted October 11, 2012 Im going to guess 490-500 whp after tuning! That would be awesome!!! I don't think that much yet, not until the heads and longtubes go on. SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
sprkn_ranger Posted October 11, 2012 Report Share Posted October 11, 2012 Man that's gotta be exciting to be getting that work done on the engine. Check out my build log! 4 Havocs in a blowthrough http://www.stevemeadedesigns.com/board/topic/187506-sprkn-rangers-blowthrough-build/ Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.