zack_e89 Posted July 23, 2012 Report Share Posted July 23, 2012 Would this be the way to go? http://www.homedepot.com/Lumber-Composites-Plywood-Sheathing-Subfloor-Particle-Board/Boise/h_d1/R-202089064/h_d2/ProductDisplay?catalogId=10053&langId=-1&productId=202089064&storeId=10051 Also, what about 2x2's? Quote 97 Suburban 8 custom PSI Platform 3 18's Link to comment Share on other sites More sharing options...
Ballen194 Posted July 23, 2012 Report Share Posted July 23, 2012 i think the price per foot ratio is cheaper if you buy full sheets and cut what you need Quote 98 Isuzu Rodeo Pioneer Deh-6300ub SUBS*Upcoming* SSA Xcon 18 4th order AMP Banda 3500 Mids/Highs Pioneer EQ Clarion EQS746 ETC. Two 1/0 run's KnuKoncepts 1/0 big 3 Shuriken BT-100 under the hood Shuriken BT-120 in the back Link to comment Share on other sites More sharing options...
Cashdollar2009 Posted July 23, 2012 Report Share Posted July 23, 2012 Jesus, you should stock up with it at that price. And what are you asking for in regards to 2x2's? Quote 1997 Chevrolet Cavalier Two 12" DC Audio XL M2'sCrescendo Audio BC5500d Current Scores: 150+ out the Trunk On 6/30/2011 at 1:11 AM, 'Ray' said: Acoustical energy is free. Electrical energy is not. Link to comment Share on other sites More sharing options...
bassface Posted July 23, 2012 Report Share Posted July 23, 2012 Alot easier to carry then full sheets. Unless you are building something huge. Quote Link to comment Share on other sites More sharing options...
Cashdollar2009 Posted July 23, 2012 Report Share Posted July 23, 2012 ..... I just realized it was for a 2x4 sheet.... Get your cut sheet made up and take it in. Have them use their panel saw and cut each pice an inch too big each way and then take them home to re-measure and clean them up. Their panel saw will be off a little bit plus they aren't going to be too precise with it. Now you saved money by buying in bulk AND you can fit all of the pieces into your vehicle just fine. And just shaving off an inch on each piece is a lot quicker than doing all of it yourself and working with a huge board. Quote 1997 Chevrolet Cavalier Two 12" DC Audio XL M2'sCrescendo Audio BC5500d Current Scores: 150+ out the Trunk On 6/30/2011 at 1:11 AM, 'Ray' said: Acoustical energy is free. Electrical energy is not. Link to comment Share on other sites More sharing options...
zack_e89 Posted July 23, 2012 Author Report Share Posted July 23, 2012 (edited) Thanks a lot guys. fyi this is the cut list i will go in with: Cut List top and bottom: 3x - 38"x22" front: 32.25"x18.75" sides: 2x - 21.25"x18.75" back: 37.25"x18.75" port: 14.75"x18.75", 10"x18.75", and 3.75"x18.75" 45° corners: 5"x18.75" in the port, 2x - 3"x18.75" in the chamber bracing: Using 2x2's, cut one 18.75" long and another 20.5" long. Also, cut 2x - 4" triangles to better brace the left side of the box. Edited July 23, 2012 by zack_e89 Quote 97 Suburban 8 custom PSI Platform 3 18's Link to comment Share on other sites More sharing options...
Blue Posted July 23, 2012 Report Share Posted July 23, 2012 The thing is about those small sheets is that they are stored vertical and they warp. So it's a crap shoot trying to find a non warp one. Quote formerly known as Blue86f150 its a 4th order just because its tuned in the 40z doesnt mean it wont reach down and jiggle your balls at sub 30 hz frequencies. Regardless if they were dipped platinum and were stuffed in Beyonce's twat.....way too fucking exspensive this sux camel dicks Link to comment Share on other sites More sharing options...
zack_e89 Posted July 23, 2012 Author Report Share Posted July 23, 2012 The thing is about those small sheets is that they are stored vertical and they warp. So it's a crap shoot trying to find a non warp one. thanks for the info blue Quote 97 Suburban 8 custom PSI Platform 3 18's Link to comment Share on other sites More sharing options...
Chris Davis Posted July 24, 2012 Report Share Posted July 24, 2012 Not sure how good there mdf and a word of caution stay away from the hardwood plywood if you want to go that route later its complete garbage or atleast over here the layers seperate with a furry. And you can by a full sheet and they usually will rip it down to what ever size you want meaning it ripping it in half , and have carts for easy move to the car lol. Quote Link to comment Share on other sites More sharing options...
bassface Posted July 24, 2012 Report Share Posted July 24, 2012 Its mdf, how good does it have to be? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.