Jump to content

Homemade Super-Neo Woofer: THE CHEVELLE RESTORATION IS DONE, dampener recommendations??

Dwn4BassAlan

Recommended Posts

STEvil Newbie

STEvil

Posted
Posted

whatever you do, be careful when you put the top on because it'll do more than break a finger lmao

MickyMcD - "Capable of making some serious trouser flapping volumes at where's-my-testicles frequencies, the Servo-Drives used to be fairly jaw dropping..."

Any time you have have a power wire next to your frame put some rubber hosing (or cut up an innertube) around it. The wire is bound to wiggle (due to driving or flex) and the casing will eventually wear through.

Hammerdown... 1%

no links to outside websites, business related FB/YT pages allowed.

775Tundra Newbie

775Tundra

Posted
Posted

I am imaging how your gonna put the top plate on with the drill press. You better have two grown ass men holding onto the lowering guide.

2003 Tahoe

dc 7.5k

dc level 5 15's (3)

MMats 341's

xs power batts

lots of sky high cable

dual alts(came off the sky-high gmc and don't know who made them)

ipad in center console

vu-din in center console

all being ripped out and being sold

STEvil Newbie

STEvil

Posted
Posted

I am imaging how your gonna put the top plate on with the drill press. You better have two grown ass men holding onto the lowering guide.

as long as the lowering guide doesnt put their fingers under the top plate.. that fucker's gonna have a lot of pulling force.

MickyMcD - "Capable of making some serious trouser flapping volumes at where's-my-testicles frequencies, the Servo-Drives used to be fairly jaw dropping..."

Any time you have have a power wire next to your frame put some rubber hosing (or cut up an innertube) around it. The wire is bound to wiggle (due to driving or flex) and the casing will eventually wear through.

Hammerdown... 1%

no links to outside websites, business related FB/YT pages allowed.

CJ18 Newbie

CJ18

Posted
Posted

have fun with that top plate. That is gonna be a beeeeeooocccchhhhhhh

Don't remind me, I'm literally dreading the moment I have to deal with that. I was thinking, "Oh, I'll just put a wooden shim around it or something". then I realized how tight the gap was and how thin the shim would be, I'm not actually sure it's possible to even get the top plate on without snapping to the center pole lol. Should be fun.

This is what you are in for.

Nikitaaa Newbie

Nikitaaa

Posted
Posted

have fun with that top plate. That is gonna be a beeeeeooocccchhhhhhh

Don't remind me, I'm literally dreading the moment I have to deal with that. I was thinking, "Oh, I'll just put a wooden shim around it or something". then I realized how tight the gap was and how thin the shim would be, I'm not actually sure it's possible to even get the top plate on without snapping to the center pole lol. Should be fun.

This is what you are in for.

Sounded like a friggen earthquake when the top plate hit the neos..

2007 M/T Honda Civic Coupe EX

(4) Sundown Audio X-8's

(2) Ampere Audio 3800.1's

(3) Stinger SPV-44 Batteries

(1) Mechman 240

3:1 Ratio 4th order sealed from the trunk

TEAM NWSPL

Best termlab scores to date in Honda trunk:
151.7db legal (official) IASCA trunk 3 class

Best termlab scores to date in my walled Subie:
152.9db legal (unofficial) IASCA advanced 2 class
155db outlaw

cjvue Newbie

cjvue

Posted
Posted

Yup^^.... seen the vid before. Shit is serious lol

My Build Log- T E A M S U N D O W N A U D I O -

2013 DbDrag WF SS1-2 - 5th Place 154.6db

2013 MECA Mod3 CA State Final Champ 153.4db

Powered by: Sundown Audio

Rich Schenk Newbie

Rich Schenk

Posted
Posted

that woofer looks brutal as hell. GL on it

On 3/28/2014 at 4:22 PM, KyLar96 said:

Its all about the music anyway..... Do a proper install, something your happy with, Fuck everyone else...... improve in time, where you can..... its not rocket science...

Tiburon build //www.stevemeadedesigns.com/board/topic/174059-97-hyundai-tiburon-build-from-ramming-to-slamming-slow-5k-build/

2000 Mountaineer build http://www.stevemeadedesigns.com/board/topic/186736-2000-mountaineer-build-from-ramming-to-slamming-part-iislow-5k-builddc-audio-americanbassxspowersingerarcaudiostingershcavideo-on-pg7/

2000 Mercury Mountaineer: Electrical:Singer 360 hairpin powdercoated white alt, Big 4 double run 1/0 SHCA OFC, 4 runs 1/0 OFC SHCA, limitless 70ah, HU: Pioneer deh80prs interiors: Skar sk85.4 on sb acoustics neo dome tweeters 2 Mmats sq4100s on 4 silver flute 8s(4ohm) SUB Stage: 3 DC5K [email protected] on 6 ascendant audio mayhem 12s d1.4s fully loaded

Dwn4BassAlan Newbie

Dwn4BassAlan

Posted
  • Author
Posted

I am imaging how your gonna put the top plate on with the drill press. You better have two grown ass men holding onto the lowering guide.

as long as the lowering guide doesnt put their fingers under the top plate.. that fucker's gonna have a lot of pulling force.

I'm not using the drill press to put it on, just to drill out the holes for the basket. It's all cast iron and steel so if I brought the base plate even even a few feet of his workshop, I would not be taking it home............. He's got steel work benches and machinery everywhere. It would be a magnetic blood bath......

you better hope your spiders keep that coil stupid linear

Lol right? I was like, we need something other than bolts for the basket, if the damn thing wasn't aluminum I would GTAW the crap out of that basket and have absolutely no movement possibility whatsoever. But it's aluminum, so I'm screwed since I don't have a friction welder nor do I know how to do explosive welding.....

The screws it came with are childs play, they look like stainless grade 3's, I'm gonna find some bigger grade 8's tomorrow..

That's also why I have the pole extruding further than the top plate, just in case the xmax gets a little too nuts it won't slide around.

Biomedical/Behavioral Science Major, The (Self-Proclaimed) Undisputed-Homemade-Woofer-King

Super-Neodymium-Woofer Build Log: The D4BA-V.2 http://www.stevemeadedesigns.com/board/topic/169236-diy-super-neodymium-woofer-build-log/?p=2475620

Fucking love Alan you goddamned fucking super nerd lol

When Alan uses big words I don't understand

It's warming up enough that the donut-punching cyclist douchenozzles are getting their two wheeled fagmobiles out.

Everytime I see a guy driving a mini cooper I cant help but think he loves cock & (2/29/16)-My wife just bitched at me about throwing out things we don't really use. My response of well we don't really use your vagina so should we throw that out was evidently not the right response. I had to leave the room.

I missed Alan.

RIP 5/29/15 - I love you son.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Who's Online   0 Members, 0 Anonymous, 651 Guests (See full list)

    • There are no registered users currently online
×
×
  • Create New...