Deadly hertzz Posted December 25, 2013 Author Report Share Posted December 25, 2013 Finally arrived in the mail !! 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
alaskanzx5 Posted December 25, 2013 Report Share Posted December 25, 2013 Now find the Max volume distortion free for the hu. Then hook the dd1 up to the line driver and set it at it's Mac distortion free point. Here is the tricky part, check the voltage on the line driver. If it's above 6volts turn it down until it's at or below 6volts. Don't turn it up higher if it id already below 6volts just because you want it at6 volts because turning it higher from what the dd1 determined to be it's max non distorted setting will create distortion. Then put the dd1 on the amp and adjust the gain for no distortion. t1500bdcp 2 t2d4 15" 1 t600.4 1 t400.2 1 set p1 tweets singer alt, tons of wiring, smd vm-1, 80prs, back seat delete, still in the works, aiming for a 145-147 with the ability to play 25hz up to 50hz. Link to comment Share on other sites More sharing options...
Brent Anderson Posted December 25, 2013 Report Share Posted December 25, 2013 I would just buy the dd-1. I don't have one at the moment ither but ill be buying it when I get my CT sound at 2500.1D and just realized you got one haha well good job getting it Link to comment Share on other sites More sharing options...
Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 Ok so after I set the head unit now I'm on to the line driver what track should I use to determine where to turn the gain up on the line driver 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
goldeneye4564 Posted December 26, 2013 Report Share Posted December 26, 2013 I RREEALLY ANGRY WIT U PHOTOBUCKET. HAD TO USE DROPBOX NOW HOLYYYYYY. Wanna ride bikes? Quote On 9/16/2017 at 3:28 AM, Jake Pace said: Oh i know how a 12v system works I did take 3 years of electronics in High school hands on and some in college and also worked on cars in college an always got A's to B's in each class. But oh well enough dealing with ppl who have probably not even lived as long as ive been into electronics! On 7/8/2013 at 4:01 AM, Banshee421 said: Do horns get low Link to comment Share on other sites More sharing options...
Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 The same as I'd use on the amp ? 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
hazestorm23 Posted December 26, 2013 Report Share Posted December 26, 2013 The same as I'd use on the amp ?I thought you were removing the line driver? Link to comment Share on other sites More sharing options...
Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 I'd have to pull my box out to re run my RCAs to reach the opposite side of my amp and I don't want to use little adapters to extend them everything was ran close and tight to were the amps and line driver was mounted, I could remove but the box is on a sub frame that's bolted to the floor so it's just a bitch to try and do that 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
goldeneye4564 Posted December 26, 2013 Report Share Posted December 26, 2013 whats the difference when you blow your amps from using the line driver you are going to have to get it out anyways I RREEALLY ANGRY WIT U PHOTOBUCKET. HAD TO USE DROPBOX NOW HOLYYYYYY. Wanna ride bikes? Quote On 9/16/2017 at 3:28 AM, Jake Pace said: Oh i know how a 12v system works I did take 3 years of electronics in High school hands on and some in college and also worked on cars in college an always got A's to B's in each class. But oh well enough dealing with ppl who have probably not even lived as long as ive been into electronics! On 7/8/2013 at 4:01 AM, Banshee421 said: Do horns get low Link to comment Share on other sites More sharing options...
hazestorm23 Posted December 26, 2013 Report Share Posted December 26, 2013 I'd have to pull my box out to re run my RCAs to reach the opposite side of my amp and I don't want to use little adapters to extend them everything was ran close and tight to were the amps and line driver was mounted, I could remove but the box is on a sub frame that's bolted to the floor so it's just a bitch to try and do that well ain't that a b. That sucks man you could have set everything up in a mater of minutes without that thing. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.